• Weintek display and values from MBUS

    1
    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • RS485/M-Bus converter configuration

    2
    0 Votes
    2 Posts
    1k Views
    A
    Hi @t-kavan, We have already encountered this, unfortunately this meter does not wait for the prescribed time and responds too quickly, so that the RS485 (transmit/receive) state in the controller does not have enough time to change. The RS485 behaviour was modified in later versions of the debian packages. With the current OS image the PRO380-MB meter are already working. Best regards, Antonín Všetula - Unipi technician
  • 1-wire occasionally stops working

    7
    0 Votes
    7 Posts
    3k Views
    P
    @AVsetula I'm aware of this guide and about the OW_off_1 switch. The problem is, that it does not solve the problem in my case. As I wrote before I tried to set OW_off_1 to true and then back to false, but all the temperature sensors kept showing 0 ˚C. I haven't found any software way how to "restart" the 1W to working state. The only thing which works is restarting whole Neuron by cutting off the power. If you have any other ideas, I'll appreciate them.
  • RS485 to external Modbus RTU board

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • `cdc_acm` driver not present

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • KLEFR Electricity meter

    2
    2
    0 Votes
    2 Posts
    1k Views
    A
    Hi @ArnieX, Thank you for your post. This is a typical error when setting up communication with INEPRO/KLEFR electricity meters, and it is really necessary to be careful when setting up other devices (modbus tables). Best regards, Antonin, Unipi
  • 1W-T-IB2 + p63 jeden UTP kabel do xG18

    4
    0 Votes
    4 Posts
    2k Views
    A
    Dobrý den, zabýval jsem se tímto zapojením více a skutečně jsem odhalil problém s připojením čidla 1W-T-IB(2) k Unipi xG18. Jedná se však o vlastnost obvodu na desce. S vaším aktuálním zapojením bude nejjednodušší úpravou přepojení vodiče ze svorky +5V na svorku GND. Po přepojení již budou tyto čidla fungovat. Čidla v podlaze Vám předpokládám fungují všechny bez problémů. Poznámka: Aby bylo možné čidla 1W-T-IB(2) provozovat s xG18, stačí na svorky čidla připojit pouze dva vodiče (1W + GND), k tomu lze využít např. dvě prostřední svorky. [image: 9db450d4-fa58-4e91-8d8a-78d4eedcb9e2-obrazek.png] Přeji hezký den Antonín z Unipi
  • Reading the ModBus bus with the Patron

    4
    0 Votes
    4 Posts
    2k Views
    A
    Hi @Vesa-Kauppinen, From Unipi Patron I/O boards by: Section 1: mbpoll -m tcp 127.0.0.1 -a 0 -0 -1 -r 1003 -p 502 Section 2: mbpoll -m tcp 127.0.0.1 -a 0 -0 -1 -r 1103 -p 502 Section 3: mbpoll -m tcp 127.0.0.1 -a 0 -0 -1 -r 1203 -p 502 And from Unipi Extension using ttyNS0 port: mbpoll -m rtu /dev/ttyNS0 -b 19200 -P none -0 -1 -r 1003 -a 15 Best regards, Antonin
  • Patron: Get CPU serial number

    2
    0 Votes
    2 Posts
    1k Views
    M
    Hello @Vesa-Kauppinen, this has been subject to change between Linux kernel versions - the older one cat /sys/devices/soc0/soc_uid comes from the original iMX kernel and has been removed by NXP in newer releases. In our kernel image, we additionally preserve it for backward compatibility. However, cat /sys/devices/soc0/serial_number is a "Linux standard" provided by recent NXP kernels that we recommend using as a unique identification.
  • Can't connect evok with a third party module

    2
    1
    0 Votes
    2 Posts
    1k Views
    Martin KudláčekM
    For the record, this issue is currently being dealt with over email. Martin
  • Patron stucked after some hours

    6
    0 Votes
    6 Posts
    2k Views
    Martin KudláčekM
    Hello everyone, we have just released updated Zulu kernel, which solves this particular problem. The problem has been in the memory lock, which overused the swap, even when the swap is off on all our OS images. This has been fixed in kernel 5.10.17+. The new kernel is 5.10.35. Whole suite of OS images is currently being generated and within an hour uploaded to the Download section Thank you for reporting the issue nad have a nice day, Martin @ Unipi
  • Suggestion for IAQ re MQTT

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • Reading modbus/TCP from IAQ RW-THC not working?

    4
    1
    0 Votes
    4 Posts
    2k Views
    Martin KudláčekM
    Hi @knebb, you have verified, that the HW is working and returns correct value via standard tool. Checking and fixing your code is unfortunately beyond the scope of the free support. Thank you for understanding and have a nice day, Martin
  • Firmware on Website for RW-THC outdated?

    3
    0 Votes
    3 Posts
    1k Views
    Martin KudláčekM
    Hi @knebb, the firmware has been updated on our Knowledge Base as well: https://kb.unipi.technology/en:files:products:05-sensors:iaq Martin
  • 1-Wire 8 port hub, switched star topology

    2
    0 Votes
    2 Posts
    1k Views
    Martin KudláčekM
    Hi @Csevi, in short - the 1-Wire hub is passive device, which helps with the "linearization" of the star topology. You can find complete information about 1-Wire here: https://kb.unipi.technology/en:automation:02-glossary:1wire-hidden Best regards, Martin
  • rtlwifi module on Patron

    3
    0 Votes
    3 Posts
    1k Views
    Martin KudláčekM
    Hello @daminou53 , we have released the Patron kernel (more precisly the "Zulu" kernel - Zulu is the codename for the SBC). Here's the repository: https://git.unipi.technology/UniPi/zulu-linux. Here are the config files: https://git.unipi.technology/UniPi/zulu-linux/-/tree/zulu_5.4.70/arch/arm64/configs Best regards, Martin
  • Zadne informace o Unipi Patron

    11
    0 Votes
    11 Posts
    3k Views
    Martin KudláčekM
    Dobrý den @lukas009, ano, pokud má digitální vstup odpovídající releový nebo digitální výstup. Více o tom se dočtete zde: https://kb.unipi.technology/cs:hw:007-patron:description-of-io:01-description-of-di S pozdravem, Martin Kudláček
  • zigbee integration

    11
    0 Votes
    11 Posts
    5k Views
    P
    @tomas_hora, thank you. I have been reading more about your products and I found out that EVOK provides websockets. I was thinking that I would write a script which would process MQTT messages from a dongle and deliver them to Mervis using websocket and the other way around. Would that work? It would replace the Node-red which you suggested. Thank you for your help, Martin.
  • Unipi G100 Setup static ip on both interfaces eth0 eth1

    3
    0 Votes
    3 Posts
    2k Views
    roberts_landoR
    I fixed by simply removing gateway and dns-nameservers definitions from the eth1 file. If anyone is interested in this the solution to make this working with also the gateway check: https://www.thomas-krenn.com/en/wiki/Two_Default_Gateways_on_One_System
  • 1W-TH-IB2 communication error detection

    2
    0 Votes
    2 Posts
    1k Views
    M
    Hello @Jan-Toth, you have not specified IDE/Language used. For example, in Mervis IDE you can use the following approach: Automatic restart of the 1-Wire bus Can you share more info about the application?