• read 1W-TH-IB2 values by HTTP/HTTPS or modbus TCP-IP

    7
    0 Votes
    7 Posts
    2k Views
    C
    Hello @Bart-Delaere, unfortunately there is no definitive answer. The 1-Wire bus is technically able to connect huge amount of devices, but reality depends on cable length, quality, noise from the environment etc, so this may be trial and error for users that do not install it daily. Unipi used to sell a hub/splitter, which we do not offer anymore. Sometimes, a surge can occur in the environment, which can take down the whole bus. Unipi units (except Unipi 1/Lite) have an option to restart the bus (the bus is not restarted during normal system reboot), you can look in the Modbus table of your unit if you wish to implement it.
  • This topic is deleted!

    2
    0 Votes
    2 Posts
    2k Views
  • DirectSwitch coils are unavailable after power outage

    8
    0 Votes
    8 Posts
    4k Views
    C
    Hello @kepi, You are free to send the unit for a post-warranty repair, please see the Service conditions and form, note that here is a fixed diagnostics fee. I fully understand, the situation with Axon is unfortunate. The compute board used in the Axon series were suddenly unavailable in the Covid shortages and the manufacturer decided to discontinue them, combined with bad downstream kernel support, the Axon series had to be ended. With the Patron, this situation is vastly different, it uses our own compute board and we have full control over it, soc has long availability and good software support, so there are no worries about its lifetime. Please note that a used product can not be returned.
  • Install softare on Axon M205 to factory default

    7
    0 Votes
    7 Posts
    3k Views
    C
    @lyngaas Hello, unfortunately, booting our OS images from an SD card on Axon is not supported. Best regards, Kryštof Černý
  • RS485 GND

    5
    0 Votes
    5 Posts
    2k Views
    D
    Hi @roberts_lando, I have the exact same case , an inverter with three pins (+/-/GND) , did you found any solution ? I have a Neuron, it has also only two pins. But it has a "END" switch next to the RS485 connector thanks
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    50 Views
    No one has replied
  • axon devices availability

    2
    0 Votes
    2 Posts
    1k Views
    A
    Hello, The production of Unipi Axon units was discontinued. The Axon line was replaced by the next generation named Unipi Patron. Best regards, Antonin
  • UNIPISPI spi0.0: SPI transfer failed

    9
    0 Votes
    9 Posts
    4k Views
    T
    @PhilesG Would you please try to update the our kernel modules to the latest version? You can do this by apt update && apt install unipi-kernel-modules or by rewriting the whole OS by a new one from https://kb.unipi.technology/en:files:software:os-images:00-start#axon_generation_os using this guide https://kb.unipi.technology/en:sw:01-mervis:running-on-axon-hidden#flashing_the_os
  • Wifi problem on Axon M565 LTE

    3
    0 Votes
    3 Posts
    1k Views
    O
    Hello Martin Triska, I clearly understand that a Wifi connection in a metal enclosure, close to an LTE modem is not great and that it could affect performances. Even if here, I am not using LTE and I disabled the module to be sure about that. The problem is clearly not a performance issue. Even if the connection was unstable or lost, the on board Wifi adapter is not supposed to fail like that. This is clearly an hardware bug/fault, independent of Wifi performance. The message log "brcmf_sdio_firmware_callback: dongle is not responding" is quite clear about that. Also, where do you explain in your catalog that this Wifi adapter is designed for occasional service or initial setup ? We were clearly not aware of that before buying them. Regarding the quantity of Neurons/Axons we are using, I was excepting a better support than your answer. Sorry, I had to say it. Regards. Olivier.
  • 0 Votes
    3 Posts
    1k Views
    M
    FYI, it looks like OS 2.2 just doesn't have mDNS/avahi enabled. I've tried it on the M525 and an M505. I was on a different network so I was trying to find the IP address with avahi, and then resorted straight to flashing it when I couldn't find it. It looks like IDE 2.1.3 doesn't support the M525. I've got a solution with two existing M505s I wanted to add it to but it doesn't even show up as an option in the manual device list. Do I have to upgrade my solution to IDE 2.2.0 to add the M525? It looks like this will require me to upgrade the OS on the M505s (from 1.9), correct?
  • RS232 GND pin

    2
    0 Votes
    2 Posts
    1k Views
    Martin KudláčekM
    Hello @rtatibouet, the RS485 and RS232 are completely different buses. The RS485 is differential and doesn't need the GND, since the logic levels are based on the voltage difference between A and B terminal The RS232 is not differential and the TX / RX logic levels are based on the voltages between TX and GND and RX and GND. Best regards, Martin
  • LTE connection problem on M265

    2
    0 Votes
    2 Posts
    1k Views
    M
    Hello @daminou53 , what OS image are you using? Have you done any changes in network configuration (e.g. /etc/network/interfaces files)? On the following lines, the connection is successfully initialized (probably with very poor signal quality) but immediately, the LTE service is restarted. 2019-02-14 11:31:58,599 - DEBUG - WAN IP 10.34.177.115, Private IP 10.21.8.1; NON-CONFLICT 2019-02-14 11:31:58,600 - INFO - WAN IP ADDRESS: 10.34.177.115 INTERFACE IP ADDRESS: 10.21.8.1 2019-02-14 11:31:58,602 - DEBUG - RSSI: 19 sigqual: 6 net-type: 7 2019-02-14 11:32:00,023 - INFO - unipi-lte version 0.18 from 2019-02-14 11:11:00.068002 - Logging started.. Are you able to provide remote access to the unit? In the meantime, you can try to install the new beta version: sudo apt install unipi-lte=0.19*
  • Image restore problem

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • Error adding controller to Mervis IDE (HW capabilities)

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • Shutdown process / status display.

    2
    0 Votes
    2 Posts
    1k Views
    Martin KudláčekM
    Hi @beergeek, there is probably a number of ways how to do it. This could be one of them: create /usr/local/sbin/shutdown and add the exec bit to it in the script, specify the logic - get the IOs into safe state and/or light up the user LEDs at the end of the script, call shutdown -h now The logic can use the SysFS approach such as this: echo 1 > /run/unipi/io_group1/do_1_01/do_value # sets DO1.1 to true Although you don't have the user LEDs available in the SysFS right now. For that, you can use mbpoll and set it via ModbusTCP. Best regards, Martin
  • Axon M505 SWUpdate gives error

    2
    0 Votes
    2 Posts
    2k Views
    Martin KudláčekM
    Hi @vesa-kauppinen, this is a soft error and you don't need to worry about it. Martin
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    29 Views
    No one has replied
  • Axon M205 Modbus Wrong telegram :05

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • I2C bus stopped working on Axon after apt upgrade

    3
    0 Votes
    3 Posts
    2k Views
    T
    The I2C is working as you can see in the output of the i2cdetect. However the ds2482 module is not loaded. You can load it on hand using modprobe ds2482 and see if the address 0x18 in the i2cdetect will be marked with UU and you should see the list of connected 1wire devices in the /sys/bus/w1/devices/
  • Disable unipi modbus tcp service

    3
    0 Votes
    3 Posts
    2k Views
    roberts_landoR
    @tomas_hora it's not a security issue but as I'm using another plc runtime with a local modbus tcp master running on port 502 unipitcp service was blocking it. I have disabled it and modbus has started working correctly