• Is there any planned date for new EVOK web interface release/finish?

    1
    0 Votes
    1 Posts
    2k Views
    No one has replied
  • 1wire sensors returns 85°C or "null"

    5
    0 Votes
    5 Posts
    3k Views
    T
    @roberts_lando Do you have the possibility to check the RJ45 connectors of the sensor or better make a new ones?
  • Change 1wire sensors refresh interval UniPi Neuron S103

    4
    0 Votes
    4 Posts
    3k Views
    T
    @roberts_lando The values are updated on the web interface over websocket as soon as it is red from the sensor... So there should be no delay in it. Have you tried changing the temperature rapidly? Right there is no support for removing the sensor from the list. But there is a parameter in the message from evok to the web ui that the sensor is lost...
  • Reset DI Input Counter

    2
    0 Votes
    2 Posts
    2k Views
    T
    @roberts_lando Support for Neurons is limited only to set the outputs and read inputs. Setting counter is not possible using Evok but if you want, you can use the TCP Modbus interface for that. Yes, once the maximum number of counter is reached it is reset to 0.
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    10 Views
    No one has replied
  • Node-red missing rpi_gpio/wron naming

    4
    0 Votes
    4 Posts
    3k Views
    S
    @zeus I was just looking at this same issue, I think its because the GPIO's in question are tied up with SPI so dont show in Node-Red. If you find a way to get them to be visible in node-red id love to know. I can connect to I01-I06 & I11 only on the UniPi 1.1
  • can't connect to evok in browser

    6
    0 Votes
    6 Posts
    4k Views
    V
    Any upgdate on this ?
  • EVOK and websockets

    3
    0 Votes
    3 Posts
    3k Views
    L
    True, if "cmd":"set" addet to json string, ws command works. Reliability of ws is not as expected - bmo it is beter to use http post methods. ps. Can you please tell what are other commands in cmd?
  • loosing 1-wire DS18B20 sensors during opreation in node-red

    5
    0 Votes
    5 Posts
    4k Views
    L
    I did as sugested I grounded cables for 1wire network connection. But it doesnt solve the issue. I guess it has to be power issue - I have 1x Unipi, 1x Rasperry Pi 3 and 1x EMO-8R module in addition 14x 1wire DS1820 temperature sensors. I am trying to figure out maximal power needed and so far I come with: 1.5mA/1wire DS18b20 1.5A/Unipi+RPi - 2.5A - RPi 3 model B (but only 1.1A is provided through Uni.pi) in opreational mode 250-500mA, that leaves around 1A for UniPi board and another 750mA for EMO-R8. Bottom line 2.4A should be enough for uni.pi main board, but not necesaray for extension module - could this cause 1wire lost problems?
  • Pushbuttons in node-red with websockets

    4
    0 Votes
    4 Posts
    3k Views
    T
    @Niko-Raes Exactly, its polls per second. Honestly, I have not tried the maximum because it depends on the exact model - with more IOs there are more values to be read which results in smaller possible polling rate.
  • evok neuron http post problems

    1
    0 Votes
    1 Posts
    2k Views
    No one has replied
  • reduce Interval from DS18B20 Sensor

    2
    0 Votes
    2 Posts
    2k Views
    D
    so i reply my self. i uncomment the following lines in evok.conf [SENSOR_1] ; onewire thermometer bus = 1 ; link to OWBUS_X address = 28FF449D711604A1 type = DS18B20 interval = 1 so, you can see the intervall is reduce to 1s. {"interval": 1, "value": 22.55, "circuit": "1", "address": "28FF449D711604A1", "time": 1494087547.135313, "typ": "DS18B20", "lost": false, "dev": "temp"} cu daniel
  • unica sensors not working

    6
    1 Votes
    6 Posts
    4k Views
    B
    Ok... I commented in the DS2438 part in owclient.py and added 'sens.vis' for the light sensor, seems to work so far... Anything missing?
  • Read Inputs with Python

    4
    0 Votes
    4 Posts
    4k Views
    T
    @s0fralk Basically yes, I recommend websocket but it is up to you what is your approach. That is for those, who want to develop their own application like Evok which will take care of the low level work with GPIOs and I2C.
  • Neuron extensions

    2
    0 Votes
    2 Posts
    2k Views
    T
    Hello @jilet, I am sorry but unfortunately not. The work is however in progress. I will try to push the update asap.
  • WebSockets and UniPi Neuron

    3
    0 Votes
    3 Posts
    2k Views
    V
    Hi @tomas_hora Thanks for your reply, I thought that might be the issue. Using the WebSocket example from the evok git page works perfectly so I will build on that example. Thanks!
  • EVOK: wget/POST api only works when control panel is open in browser

    8
    0 Votes
    8 Posts
    5k Views
    M
    @tomas_hora Hi, I did a fresh Rasbian install, got the neuron online, did a git clone http..... set the permissions (as per the GIT page) started it up. and.... PERFECT! I have my python monitoring program starting automatically as a service, and I had to put a little sleep command in it on start as it was trying to run before EVOK started. Runs great. Many thanks. Merv.
  • 1Wire Sensor ID keeps changing - No w1_slave file

    7
    0 Votes
    7 Posts
    4k Views
    S
    @tomas_hora Well, I guess I did have a small typo in my owfs.conf file, but I have fixed that. Here is my current owfs.conf file: [image: 0_1490041735702_UniPi_4.JPG] All the lines above these are commented out. I still see multiple sensors with invalid IDs, and there are no w1_slave files: [image: 0_1490041819222_UniPi_5.JPG] Thank you again. Steve
  • 1Wire temperature sensor not showing

    2
    0 Votes
    2 Posts
    2k Views
    T
    @paulot Do you see the device with address 18 on the i2c bus? Issue i2cdetect -y 1
  • Noob question - Any HTML examples out there?

    2
    0 Votes
    2 Posts
    2k Views
    T
    Hello @SOswald and welcome to the community. First of all I am sorry that there is still not enough documentation or examples. We designed EVOK only to act as API which provides easy access to all IOs of UniPi including basic web interface providing overview of state of IOs and basic configuration. It is not a designed to act as a example of a application for complete description of behavior or visualization of the sysytem. So if you like coding, take a look e.g. at Node-Red. We have made simple example of communication using websockets on it and you can also easily build nice web interafes using Node-Red.