• Hardware Request: Hirose U.FL connector on board

    4
    0 Votes
    4 Posts
    2k Views
    Martin KudláčekM
    Well @nicola-mondinelli, you should submit it to the manufacturer of the Raspberry Pi. We buy stock Raspberry Pis just like everyone else. Best regards, Martin
  • Neuron L303 and M303 DI not working -- LED not showing

    9
    0 Votes
    9 Posts
    3k Views
    Martijn HemeryckM
    @martin-kudláček said in Neuron L303 and M303 DI not working -- LED not showing: mbpoll 127.0.0.1 -a 0 -0 -1 -r 1136 mhemeryck@L303-sn17:~ $ mbpoll 127.0.0.1 -a 0 -0 -1 -r 1130 mbpoll 1.4-12 - FieldTalk(tm) Modbus(R) Master Simulator Copyright © 2015-2019 Pascal JEAN, https://github.com/epsilonrt/mbpoll This program comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to redistribute it under certain conditions; type 'mbpoll -w' for details. Protocol configuration: Modbus TCP Slave configuration...: address = [0] start reference = 1130, count = 1 Communication.........: 127.0.0.1, port 502, t/o 1.00 s, poll rate 1000 ms Data type.............: 16-bit register, output (holding) register table -- Polling slave 0... [1130]: 50 mhemeryck@L303-sn17:~ $ mbpoll 127.0.0.1 -a 0 -0 -1 -r 1137 mbpoll 1.4-12 - FieldTalk(tm) Modbus(R) Master Simulator Copyright © 2015-2019 Pascal JEAN, https://github.com/epsilonrt/mbpoll This program comes with ABSOLUTELY NO WARRANTY. This is free software, and you are welcome to redistribute it under certain conditions; type 'mbpoll -w' for details. Protocol configuration: Modbus TCP Slave configuration...: address = [0] start reference = 1137, count = 1 Communication.........: 127.0.0.1, port 502, t/o 1.00 s, poll rate 1000 ms Data type.............: 16-bit register, output (holding) register table -- Polling slave 0... [1137]: 65535 (-1) Right, so it indeed looks like a very high debounce time! Strange, since I thought I had already checked that with the web view / can't recall changing it myself. Anyways, I ran the firmware updates again, and now it's fixed! Thanks a lot!!
  • 0 Votes
    8 Posts
    2k Views
    B
    Thanks a lot. I am planning some extensions to my system, so I might want to use the discount you promised :) Btw, any reason why DI/DO lines are registered as separate GPIO chips, instead of using a smaller number of chips each with 16/14 lines?
  • After upgrade Neuron M103 appeared new virtual relays 2.09-2.16

    2
    0 Votes
    2 Posts
    1k Views
    B
    FIxed in EVOK 2.1.6. Thanks. But all aliases were deleted. I had to configure all aliases again.
  • Neuron L203 DI not working

    4
    0 Votes
    4 Posts
    2k Views
    Martijn HemeryckM
    I have a similar for my Neuron L303. I didn't check via Mervis, but I just noticed that the indicator LEDs on the unipi itself was not reacting in any way anymore for some specific DI (others still working). Do you think this is due to the same firmware issue or a more fundamental hardware issue? And why would I only have this issue now? I have only been running my unipi for some debugging purposes up until now (it's just when experimenting with my actual full set of push buttons that I started to notice this).
  • spi_master spi0: spi0.1: timeout transferring

    4
    0 Votes
    4 Posts
    2k Views
    B
    Neuron, after apt-get upgrade $ sudo /opt/unipi/tools/fwspi -i 0 Boardset: 0 B-1000 (v1.0) Baseboard: 0 B-1000 (v0.6) Firmware: v5.27 sudo /opt/unipi/tools/fwspi -i 1 Boardset: 1 E-8Di8Ro (v1.0) Baseboard: 1 E-8Di8Ro (v0.2) Firmware: v5.27
  • no neuron eeprom data detected after restarting the unit

    2
    0 Votes
    2 Posts
    1k Views
    T
    @stephane-clavel Do the RUN leds blink? Did you save the direct switch configuration to NV ram or do you set ip up again after boot? Can you provide the output of i2cdetect -y 1 ?
  • 3G/4G for Unipi Neuron S103-G available ?

    4
    0 Votes
    4 Posts
    2k Views
    Martin KudláčekM
    Hello @asunc, absolutely no problem. The Axon is running a debootstraped arm64 Debian with added repository of our packages via which we publish fixes and new versions of our software. Best regards, Martin
  • S103-G use GSM/GPRS module to connect to internet

    Moved
    29
    0 Votes
    29 Posts
    23k Views
    T
    The issue was by the incorrect comm speed with the modem. I modified the guide provided by @roberts_lando to use the proper baudrate of 9600 instead of 115200.
  • About the relays

    3
    0 Votes
    3 Posts
    2k Views
    H
    @barnabás-králik said in About the relays: I'm thinking about using an L403 for controlling a large number of blinds (apart from other building automation duties) with 2 relays per blind motor. Why not go for TCP-IP solution, i use a Kincony kc868-h32, a 32 relay solution, that you can steer the relays true a url link command, works fine for me. There are similar solutions more hobby orientated, and more pro, over Modbus, serial and TCP-IP, there are also 2/4/8/16 solutions out there, so that you can have your relays close by what you wane control, and only have to run a network or serial cable to the relay unit. https://www.youtube.com/watch?v=RVWvRN8yKWs [image: alt text]
  • pulse counter with neuron

    Moved
    11
    0 Votes
    11 Posts
    5k Views
    Martin KudláčekM
    Helo @jos0, the name "holding register" doesn't mean the value is stored in the non-volatile memory. This is just a type of the data store which comes from the Modbus naming convention, which means it can be read and written into, as oppose to the Input register, which can be only read. You can save the current value of the counter register with the saving of the current values to internal flash. This save can be initiated by e.g. setting the coil named "Save current configuration and use on startup" which has to be called on the appropriate group. We do not recommend to do it very often as this will corrupt the internal memory. Try solving the problem in the program instead. Best regards, Martin
  • Testing DI through DO?

    3
    1
    0 Votes
    3 Posts
    1k Views
    Martin KudláčekM
    Hi @knebb, definitely not. The DOs are NPN type (open collector). You can read more about how to read the NPN outputs with digital inputs here: https://forum.unipi.technology/topic/712/neuron-12v-digital-input/2 Best regards, Martin
  • Analog Output- which regsiter to use in modbus?

    3
    0 Votes
    3 Posts
    1k Views
    Martin KudláčekM
    Hi @knebb, there are two approaches and you figured out both of them: Do the calculation and write to register 2 Write a value to the register 3000. The value has to be 32bit signed integer. I checked the documentation and I think there is a mistake with the registers 3000, 3001 and 3002. Those should be 3000, 3002 and 3004 since the 32bit values need two consecutive registers. I will check what is in the firmware and let you know! Best regards, Martin
  • Internal ModBUS problem

    6
    0 Votes
    6 Posts
    3k Views
    ntdN
    @ntd said in Internal ModBUS problem: I will update this thread when I will have some news. Well, I installed the new SD card a couple of months ago and received no complaints ever since, so I suppose this update solved the problem. @Martin-Kudláček: thanks again for your support .
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    10 Views
    No one has replied
  • M503 AO Problem

    2
    0 Votes
    2 Posts
    1k Views
    Martin KudláčekM
    Hello @raedhammad, this looks like a HW issue. Are you sure you didn't draw more than 20mA from the analog output? That would certainly destroy it. Best regards, Martin Kudlacek
  • Neuron with 6 relays like unip1.1 lite?

    2
    0 Votes
    2 Posts
    1k Views
    Martin KudláčekM
    Hi @juntiedt, there is a M103 with 8 relays.
  • Firmware upgrade on L503

    Moved
    5
    0 Votes
    5 Posts
    3k Views
    Martin KudláčekM
    Hello @origami, the UniPi 1.1 doesn't need any firmware. To use the newest set of tools, do full update & upgrade of the operating system. Best regards, Martin
  • Example application neuron - evok for home automation

    Moved
    5
    0 Votes
    5 Posts
    4k Views
    J
    Hi Martijn, I am also trying to read analog and digital ports on unipi to collect sensor data from few sensors. I was also just wondering if we can do it in the same way like we do it on raspberry pi using a python script. I can see that even you wanted to do something like that. I have also gone through evok api but they seem to be specific models. I dont think using that we can directly read analog and digital I/Os on unipi. Can you please suggest any ideas if you were successful doing that? Thanks, Jitu
  • RFID modul přes RS485

    3
    0 Votes
    3 Posts
    2k Views
    S
    Mockrát děkuji za odpověď.