• Relays stopped to work.

    6
    0 Votes
    6 Posts
    3k Views
    T
    @CKB That is correct, 0x32 is already taken by the relays on UniPi so you can theoretically add only 7 of EMO-R8
  • SPI Ports

    2
    0 Votes
    2 Posts
    2k Views
    T
    @maci23 check the documentation and RPI pinout. You might need to get rid off some Digital Inputs.
  • Unipi 1

    8
    0 Votes
    8 Posts
    5k Views
    T
    @kurt That you have to enable pull-up resistors for each GPIO that is connected to Digital Input in order to be able to read the status of digital inputs... btw check https://forum.unipi.technology/topic/54/windows-10-iot
  • Operation HMI via display on the Unipi

    3
    0 Votes
    3 Posts
    2k Views
    R
    Hello, Thank you for your quick response! Then I'll probably take a second Raspi or a cheap tablet ...
  • Unipi input don't work

    2
    0 Votes
    2 Posts
    2k Views
    T
    @Pietervandoren run systemctl stop evok and then start it manually: /opt/evok/evok.py and share the output here. https://github.com/UniPiTechnology/evok#debugging
  • Relays not shown on the Evok API

    6
    0 Votes
    6 Posts
    5k Views
    T
    And the /boot/config was the same @s0fralk? Because every board and cable is tested before we ship it. Was it working for at least a while? Could you please provide the serial number of your UniPi?
  • How to connect the relay properlyThanks in advance

    2
    0 Votes
    2 Posts
    2k Views
    T
    Hello @Daniel-Lang, your schematics is correct. Switching the L is the way.
  • PWM setup issue used with codesys

    2
    0 Votes
    2 Posts
    3k Views
    T
    @lefrank01 GPIO18 already used for AO as stated in the documentation
  • Digital Input Triggered by Motion Sensor

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • Unipi mit USV

    2
    0 Votes
    2 Posts
    2k Views
    T
    Hello @n.sawas, you should definitely use the PIUSV with the JP1 DISmounted as you will be powering the RPi via the microUSB right?
  • EMO-R8 RJ45 ??

    2
    0 Votes
    2 Posts
    2k Views
    T
    @Alverman Sorry, Typo fixed.
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    2 Views
    No one has replied
  • Problems switching a relay

    2
    0 Votes
    2 Posts
    2k Views
    T
    @Daniel-Richter Relays are not connected to GPIO, they are connected via MCP23008 on the I2C bus, as stated in the documentation.
  • 0 Votes
    3 Posts
    3k Views
    H
    @skorp said in How long are the UniPi 1.1 and its Extension modules gone be supported: 8 channel expander has really small number of selling, we will make Neuron S100 with 2 channels, which should be enough for the major part of our customers. Would you not consider a Expander unit, ware you can hookup the 4 remaining wires of the RJ45 to be used as free power lines? Like a 12V + 24V, 5V + 12V or 2x 5V/12V/24V, to power 1Wire sensors and devises, then you don't need of running extra power wires if they need extra power. Would be handy for things like steering a remote relay whit a DS2405. Tho i don't know if the 1Wire hub can handle those power lines.
  • Relays on a socket

    2
    0 Votes
    2 Posts
    2k Views
    T
    @zeus Thats why we do not assemble high power relays so people should use external socket relays which can be easily replaced - eg from Shack or Finder. Both have good socket relays for DIN rails.
  • DI for sense of a S0-Out use with interupt

    2
    0 Votes
    2 Posts
    2k Views
    T
    @devien if you want to use fhem, then I am not sure if it can handle interrupts on GPIOs. However, you can use evok (which provides also a counter for each DI and of course debounce) and poll evok for the counters. I have no experience with the 1Wire IC, but looks interesting :)
  • Unipi 1.1 and DS2762

    2
    0 Votes
    2 Posts
    2k Views
    T
    @zorro_66 You can, but except the OWFS itself, it is not directly supported in any software that I am aware of...
  • Neuron L403 / no useable documentation

    10
    0 Votes
    10 Posts
    6k Views
    B
    Thanks for the license!
  • Neuron M203/How to read DI?

    2
    0 Votes
    2 Posts
    2k Views
    T
    Hello, make sure set the slave to 2 as you had. Also double check the documentation, coils for DI using slave 2 are from coil 14 up to 29. You are reading coils 0-15. Br, Tomas
  • Digital Inputs I13 and I14 with RasPi 3

    4
    0 Votes
    4 Posts
    2k Views
    T
    I have updated the wiki a little bit: http://unipi.technology/wiki/Inputs_13,14 Please check the pin numbering.