• How to implement schedule with TPG gadget in HMI

    2
    4
    0 Votes
    2 Posts
    960 Views
    Martin KudláčekM
    Hi @Tase, you are trying to use variable (instance of a TPG function blok) which is in another function block. This is possible, but it is usually not good idea, since you would broke the "encapsulation" provided by the function block. What might be better is to create a HMI function block template and use it in the HMI template. Best regards, Martin
  • 0 Votes
    2 Posts
    1k Views
    D
    @Dmytro said in Error: "Write of group with index 3 skipped": Write Only On Change || False In a previous post was a mistake. Write Only On Change || True It causes error "Write of group with index 3 skipped" If that parameter has value False, error message in Port monitor disappears. Instead of that, Port monitor shows to me another problem: 15.12.2021 14:37:40.0122 => Send: 240 16 6 3 0 1 2 3 0 201 7 15.12.2021 14:37:40.0822 Timeout 15.12.2021 14:37:40.0922 => Send: 240 16 6 3 0 1 2 3 0 201 7 15.12.2021 14:37:40.1622 Timeout 15.12.2021 14:37:40.1722 => Send: 240 16 6 3 0 1 2 3 0 201 7 15.12.2021 14:37:40.2422 Timeout 15.12.2021 14:37:40.2672 => Send: 240 3 0 0 0 66 208 218 15.12.2021 14:37:40.3372 Timeout 15.12.2021 14:37:40.3472 => Send: 240 3 0 0 0 66 208 218 15.12.2021 14:37:40.3652 <= Recv: 240 16 6 3 0 15.12.2021 14:37:40.3722 <= Recv: 1 228 96 15.12.2021 14:37:40.3722 Timeout So I still cannot write the value to the register.
  • Push button relay toggle

    mervis neuron switch
    25
    0 Votes
    25 Posts
    20k Views
    John-paulJ
    @Giamba or maybe @Martin-Kudláček, i'm using this program to control my dali controler which working fine now except from the switch function. When i push my my mometary switch on HMI and keep pushing it the light slowly increases or decreases at the next push. That's all working fine. But the switch function does work fine trough the g on the sel_0. Only problem is that when i start the plc the light is off (is ok) but the input on sel_0 is true so that results in no output on the sel_0. When i keep pushing the switch on the hmi the light increases on the output of the b30 counter but not on the output of the sel_0. Only when i realease the button the sel_0 output wil be the same as the output on the BD30 counter. After the sel_0 is high on the output and the lamp is on. i can switch the lamp on/off with a short push, no problem. What i need is : Long push > increase or decrease light (even if the plc is just turned on) short push > turn light on/off. Can anyone help me with this funtion to work fine? Many regrards, John-paul [image: M203_Dimmer.png]
  • Mervis and Dali Protocol

    6
    0 Votes
    6 Posts
    2k Views
    John-paulJ
    @Martin-Kudláček I now use the Lunatone 0-10V dali controler 886468352-HS (30ma). This is working very fine on the 1-10V analog output on my M203's. We now have two units running in the field. I now can control the dali system with my hmi screen. Again thnx for the support. Best regards, John-paul
  • Checking internet connection within mervis

    3
    0 Votes
    3 Posts
    833 Views
    L
    @AVsetula Thank you for your answer, even it was not what I expected. The library of functions seems to be rather limited.
  • WEB DateTime Setter

    3
    0 Votes
    3 Posts
    981 Views
    L
    Anybody know what's wrong with my DateTime Setter gadget. I can't write from Mervis to controller (S103-G), but the other way round it working [image: 506536dd-4b03-4e0d-86d6-23a2c12fbdf2-image.png] [image: edb7b731-b349-4673-9bf6-18dd82880073-image.png] From the picures can bee seen same values, but it's write from IDE.
  • Chyba Neuron L503

    2
    0 Votes
    2 Posts
    541 Views
    C
    @Cichacek Upgrade: Včera mi to nedalo a znova jsem zkoušel různé možnosti. Jako poslední jsem vyzkoušel založit nový projekt "ZKOUŠKA" a kupodivu vše začalo fungovat normálně. Zkusil jsem zpět původní projekt a vypadá že běží. Jediné co nefunguje je WEB. Nenačítá informace z čidel, tlačítka nefungují. Čidla mají červenou tečku. Zkoušel jsem i založit nové HMI v původním projektu a stále stejná chyba. Když ale nahraju projekt "ZKOUŠKA" web normálně běží a zobrazuje teploty atd. Nevím kde jsem udělal nějakou změnu, jelikož jsem dle požadavků měnil hesla (Warning - při kompilaci).
  • Pop-up Gadget

    3
    1
    0 Votes
    3 Posts
    896 Views
    L
    Thanks alot. Now can continue again.
  • Mervis alarm variable

    3
    2
    0 Votes
    3 Posts
    999 Views
    L
    Thanks for your answer. I try a with GIF image and it working better and be visually better.
  • invalid or already used request code

    2
    0 Votes
    2 Posts
    684 Views
    A
    Hi, License request code can be used only once to obtain a license. If you use the request code for an account to which you later lose access, the license cannot be renewed and you must purchase a new license request to generate a new license. We therefore recommend using request codes only on the main account in the Unipi portal. (more about the license request: https://kb.unipi.technology/en:sw:01-mervis:getting-mervis-licence-hidden) Have a nice day Regards Antonín Všetula, technican
  • Mervis IDE tasks

    3
    1
    0 Votes
    3 Posts
    1k Views
    L
    Now it's working! Thanks!
  • Buffer size

    2
    0 Votes
    2 Posts
    717 Views
    Martin KudláčekM
    Hello @HPC, I am not sure if I understand the problem. Can you please specify what is connected to what on via which protocol / interface? Thank you and have a nice day, Martin
  • Fupla BD2 Pulse generator, wrong timing.

    3
    0 Votes
    3 Posts
    907 Views
    Z
    Hello. Thank you for reply, at least i now it's not my foult. Regards.
  • History graphs not available in SCADA

    4
    0 Votes
    4 Posts
    1k Views
    P
    @AVsetula thank you very much, this made the trick. Now, after SDcard saving update and this, my Neuron becomes finally usable for me. Thank you guys for work you are doing.
  • Add .svg pictures to Mervis project

    3
    0 Votes
    3 Posts
    882 Views
    L
    Thanks. This must try!
  • This topic is deleted!

    1
    0 Votes
    1 Posts
    3 Views
    No one has replied
  • Problem with DI and Mervis

    7
    2
    0 Votes
    7 Posts
    2k Views
    A
    Hello @HVAC-Arthus First, I recommend downloading and installing the latest Mervis IDE and Mervis OS available here: https://kb.unipi.technology/en:files:software Then open the project in a new IDE and save to convert the project to the new version. Before converting to the new version, we recommend that you always create a project archive with a suitable name. If you use the RaspberryPi 4 computing module for Unipi 1.1 / Lite, this should also solve your problem, as support for these computing modules was added only in the last version. With my RaspberryPi 4 and Mervis v2.4.0 your project works.
  • UART port (TX, RX) communication between Uni Pi 1.1 and Arduino Uno

    2
    0 Votes
    2 Posts
    933 Views
    A
    Hi Sabina, The best way to communicate between SW Mervis and third party devices is to implement the Modbus protocol on these devices. Subsequent operation and modifications are simpler and faster. Another great advantage is that this protocol basically allows you to operate multiple slave devices on one serial line. In this case, Openport is a functional block that takes care of opening the port, ie its reservation within the system. In the input string (def) for FB io.openport it is necessary to enter for UART port 1: "def: = 'serial: 1: 9600,8, N, 1';". I also enclose a tested code example in ST for Unipi 1.1.
  • Send mail - settings

    3
    0 Votes
    3 Posts
    1k Views
    Martin KudláčekM
    Hello @pavel_nadr, we have released a new version of MervisIDE, which fixes the problem. Please, follow the information in this news: https://kb.unipi.technology/en:00-start?redirect=1#new_mervis_ide_os_v240_released
  • Sending strings over TCP

    2
    0 Votes
    2 Posts
    737 Views
    Martin KudláčekM
    Hello @HPC, since Modbus doesn't know anything about data types, it is up to both the master and slave to come up with an exchange format. The registers are 16bit, but the ASCII is only 8bit. The data has to be aligned somehow, or maybe two consecutive characters can be stored into one register? Either way, the goal will be to iterate through the string and convert every item of the string array to byte. Best regards, Martin