hi @juntiedt seems like this forum have no pm funktion please drop me a mail [email protected]
Regards
hi @juntiedt seems like this forum have no pm funktion please drop me a mail [email protected]
Regards
Hi @juntiedt thats looks nice can/will you send me the flow per PM thx
Regards
Device Dead ??
I just upgraded my S103-G without any problems, but xS50 won't come up after upgrade with fwserial.
I received many Flashing errors on the cli during the upgrade (timeout & invalid data), and after that the unit was unresponsive.
I restarted the unit (after more than two hours). Before I had 4 LEDs lit up : PWR (red), RUN, RX and TX.
After reboot only PWR is lit permanently (red).
Any Help ?
regards
forget to post the system defaults
raspian-lite April 2018
root@pimatic:~# cat /etc/debian_version
9.4
root@pimatic:~# uname -a
Linux pimatic 4.14.43-v7+ #1115 SMP Fri May 25 14:27:48 BST 2018 armv7l GNU/Linux
Regards un|x
Hi
after copy from the old evok version before :
sudo cp -r tornadorpc_evok /usr/local/lib/python2.7/dist-packages
sudo cp -r opt/* /opt/
sudo cp -r evok/ /opt/
unipi start and modbus running to extension
Regards un|x
Hi
Fresh installed image image from 09.2017 raspian-stretch lite :
root@raspberrypi:/home/pi# cat /etc/debian_version
9.1
Kernel :
root@raspberrypi:/home/pi# uname -a
Linux raspberrypi 4.9.41-v7+ #1023 SMP Tue Aug 8 16:00:15 BST 2017 armv7l GNU/Linux
no apt upgrade only apt update
after install evok from git and final reboot evok not starting .
root@raspberrypi:/home/pi# service evok status
● evok.service - Evok Modbus/Websocket/Rpc Server
Loaded: loaded (/etc/systemd/system/evok.service; enabled; vendor preset: enabled)
Active: failed (Result: exit-code) since Thu 2018-05-24 19:01:39 UTC; 56s ago
Process: 503 ExecStart=/usr/bin/python /opt/evok/evok.py (code=exited, status=1/FAILURE)
Main PID: 503 (code=exited, status=1/FAILURE)
May 24 19:01:39 raspberrypi systemd[1]: evok.service: Service hold-off time over, scheduling restart.
May 24 19:01:39 raspberrypi systemd[1]: Stopped Evok Modbus/Websocket/Rpc Server.
May 24 19:01:39 raspberrypi systemd[1]: evok.service: Start request repeated too quickly.
May 24 19:01:39 raspberrypi systemd[1]: Failed to start Evok Modbus/Websocket/Rpc Server.
May 24 19:01:39 raspberrypi systemd[1]: evok.service: Unit entered failed state.
May 24 19:01:39 raspberrypi systemd[1]: evok.service: Failed with result 'exit-code'.
and
oot@raspberrypi:/home/pi# /usr/bin/python /opt/evok/evok.py
Traceback (most recent call last):
File "/opt/evok/evok.py", line 1239, in <module>
class VersionHandler(UserCookieHelper, APIHandler):
File "/opt/evok/evok.py", line 1240, in VersionHandler
self.version = 'Unspecified'
NameError: name 'self' is not defined
any tips hints ?
Regards
Hi
this day after a reboot i have the same error message and the link from S103G to xs50 not working only one short blink from the modbus rx/tx
reinstall evok and fresh image not working.
root@pimatic:~# /usr/bin/python /opt/evok/evok.py
[I 180524 19:27:48 config:63] eprom: UniPi Neuron S103 version: 1.0 serial: 0xd
[I 180524 19:27:48 evok:1634] Starting using config file /etc/evok.conf
[I 180524 19:27:48 config:75] YAML Definition loaded: M20x.yaml, type: 3, definition count 0
[I 180524 19:27:48 config:75] YAML Definition loaded: xS40.yaml, type: 3, definition count 1
[I 180524 19:27:48 config:75] YAML Definition loaded: M30x.yaml, type: 3, definition count 2
[I 180524 19:27:48 config:75] YAML Definition loaded: L40x.yaml, type: 3, definition count 3
[I 180524 19:27:49 config:75] YAML Definition loaded: L50x.yaml, type: 3, definition count 4
[I 180524 19:27:49 config:75] YAML Definition loaded: M50x.yaml, type: 3, definition count 5
[I 180524 19:27:49 config:75] YAML Definition loaded: M40x.yaml, type: 3, definition count 6
[I 180524 19:27:49 config:75] YAML Definition loaded: L30x.yaml, type: 3, definition count 7
[I 180524 19:27:49 config:75] YAML Definition loaded: xS50.yaml, type: 3, definition count 8
[I 180524 19:27:49 config:75] YAML Definition loaded: CUSTOM MODBUS DEVICE.yaml, type: 3, definition count 9
[I 180524 19:27:50 config:75] YAML Definition loaded: M60x.yaml, type: 3, definition count 10
[I 180524 19:27:50 config:75] YAML Definition loaded: L20x.yaml, type: 3, definition count 11
[I 180524 19:27:50 config:75] YAML Definition loaded: S10x.yaml, type: 3, definition count 12
[I 180524 19:27:50 config:75] YAML Definition loaded: xS30.yaml, type: 3, definition count 13
[I 180524 19:27:50 config:75] YAML Definition loaded: M10x.yaml, type: 3, definition count 14
[I 180524 19:27:51 config:75] YAML Definition loaded: L51x.yaml, type: 3, definition count 15
[I 180524 19:27:51 config:75] YAML Definition loaded: xS10.yaml, type: 3, definition count 16
[I 180524 19:27:51 config:75] YAML Definition loaded: DALI.yaml, type: 3, definition count 17
[I 180524 19:27:51 config:75] YAML Definition loaded: evok-alias.yaml, type: 2, definition count 0
[I 180524 19:27:51 evok:1698] HTTP server listening on port: 8080
[I 180524 19:27:51 modbusclient_tornado:122] SPI client started
[I 180524 19:27:51 modbusclient_rs485:333] UART client started
[I 180524 19:27:51 neuron:268] Reading the UART board on Modbus address 15
[I 180524 19:27:51 neuron:157] Reading SPI boards
[D 180524 19:27:51 owclient:377] Entering 1wire loop
[I 180524 19:27:51 neuron:172] No board on SPI 2
[E 180524 19:27:51 neuron:290] 'NoneType' object has no attribute 'get_register'
Traceback (most recent call last):
File "/opt/evok/neuron.py", line 283, in readboards
yield board.parse_definition(self.hw_dict, 1)
File "/usr/local/lib/python2.7/dist-packages/tornado/gen.py", line 1055, in run
value = future.result()
File "/usr/local/lib/python2.7/dist-packages/tornado/concurrent.py", line 238, in result
raise_exc_info(self._exc_info)
File "/usr/local/lib/python2.7/dist-packages/tornado/gen.py", line 1069, in run
yielded = self.gen.send(value)
File "/opt/evok/neuron.py", line 561, in parse_definition
self.parse_feature(m_feature, board_id)
File "/opt/evok/neuron.py", line 546, in parse_feature
self.parse_feature_ao(max_count, m_feature, board_id)
File "/opt/evok/neuron.py", line 478, in parse_feature_ao
dev_id=self.dev_id, major_group=m_feature['major_group'], legacy_mode=self.legacy_mode)
File "/opt/evok/neuron.py", line 1777, in __init__
self.offset = (uint16_to_int(self.arm.neuron.modbus_cache_map.get_register(1, self.regcal + 1, unit=self.arm.modbus_address)[0]) / 10000.0)
AttributeError: 'NoneType' object has no attribute 'get_register'
[I 180524 19:27:51 neuron:172] No board on SPI 3
[I 180524 19:27:51 config:351] Alias loaded: <neuron.Relay object at 0x7600dc70> al_lights_kitchen
[I 180524 19:27:51 config:351] Alias loaded: <neuron.Relay object at 0x7600df50> al_lights_bedroom
Regards
@Vesa-Kauppinen
Hi
have you disable the BT on Pi3
/boot/config.txt addline
dtoverlay=pi3-disable-bt
and on /boot/cmdline.txt remove
serial console than its looks like
dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=e13fdf55-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
Regards
Hi
use
[EXTENSION_1]
global_id = 2
device_name = xS30
modbus_uart_port = /dev/extcomm/0/0
neuron_uart_circuit = 1_01
allow_register_access = True
address = 15
scan_frequency = 2
scan_enabled = True
baud_rate = 19200
parity = N
stop_bits = 1
Regards
@jens
Hi
and where is the solution ?
Regards
HI
yes thats no prob i have time and my test work is allways online
but hope another user use fhem and have beginn the work.
yes the 1wire run but little scary i use 18 sensors 16 x DS18B20 and 2 from unica
but owserver have once all sensors another second 0 sensors and another sec. and so on
my owserverconf lokks like :
! server: server = 127.0.0.1:4304
device = /dev/i2c-1
server: i2c = /dev/i2c-1:ALL
server: port = 4304
but realy unstable on sensor detect.
evok have no problem to detect all sensors only the unica is detect but no data in webui :smirk:
Sensor DS2438 - 2620531402000075 N/A
Regards
Hi
is anyone use fhem 5.8 whit neuron s103-g or the xs50
and have a working config for alle the relays / dig in / dig out / 1wire
and has the desire to provide that.
thx
Regards
hi
have you disable BT ?
i have same problems whit the serial console to the gsm modem.
i have fixed whit edit the /boot/config.txt and add
dtoverlay=pi3-disable-bt
Pi 3 and stretch have problems whit bt and serial
Regards
@roberts_lando
i have found one error in another flow i have running sms sender i have delete this and the error seems only the trim see screenshots.
1
2
3
Regards
i have check the modem connect over cu and modem works and i disconnect to the modem.
Hi
yes the cu session a closed in debug i see this
3.11.2017, 11:25:11node: 96ac4186.358femsg.payload : string[4]
"OK↵"
3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[11]
"AT+COPS? ↵"
3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[17]
"+COPS: 0,0,"A1"↵"
3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[2]
"↵"
3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[4]
"OK↵"
3.11.2017, 11:25:14node: parseOperatorfunction : (error)
"TypeError: Cannot read property 'trim' of undefined"
3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[10]
"AT+CGMI ↵"
3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[18]
"+CGMI: "Fibocom"↵"
3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[2]
"↵"
3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[4]
"OK↵"
3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[10]
"AT+CGMM ↵"
3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[38]
"+CGMM: "GSM850/900/1800/1900","G510"↵"
3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[2]
"↵"
3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[4]
"OK↵"
3.11.2017, 11:25:18node: parseModelIDfunction : (error)
"TypeError: Cannot read property 'trim' of undefined"
Regards
Hi
i have inport your data but i get one error in debug
its "3.11.2017, 10:59:29node: parseModelIDfunction : (error)
"TypeError: Cannot read property 'trim' of undefined""
and the website looks like :
connect is green but no info i have only change the serial connect to
/dev/ttyAMA0: 115200-8n1
or i have problems whit the modem i can send the first sms whitout problems but after this only error when i test it whit cu -l /dev/ttyAMA0
hope for hints :smile:
Regards
Nice thx for help :smile:
Regards
HI
i use no mervis but under jessy and stretch i use
git clone https://github.com/UniPiTechnology/evok
cd evok
chmod +x install-evok.sh uninstall-evok.sh
sudo ./install-evok.sh
But warning you have to make the update over nic not wlan
in the setup there is a error when say make wlan ap .Its disconnect the Wlan
Regards