S103-G use GSM/GPRS module to connect to internet
-
@unix I have added it to node-red flows library: https://flows.nodered.org/flow/af6487676bd89e5e8b74b2c9da1e176d
Enjoy :)
-
Nice thx for help :smile:
Regards -
Hi
i have inport your data but i get one error in debug
its "3.11.2017, 10:59:29node: parseModelIDfunction : (error)
"TypeError: Cannot read property 'trim' of undefined""and the website looks like :

connect is green but no info i have only change the serial connect to
/dev/ttyAMA0: 115200-8n1or i have problems whit the modem i can send the first sms whitout problems but after this only error when i test it whit cu -l /dev/ttyAMA0
hope for hints :smile:
Regards
-
@unix Did you close the connection after using cu? Cause that error means that I call .trim() in an undefined var (modelID) that means no data is received after the command. Each command has a timeout, after that I close the read stream from the serial and I try to parse the response string, if the response string is not well parsed those errors are normal, try to put a debug node to see the output of the serial and check that the cu session is closed.
Disconnect: type ~ (alt+126) than wait for [unipi] output than type . and hit <Enter>
-
Hi
yes the cu session a closed in debug i see this3.11.2017, 11:25:11node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[11] "AT+COPS? ↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[17] "+COPS: 0,0,"A1"↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[2] "↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:14node: parseOperatorfunction : (error) "TypeError: Cannot read property 'trim' of undefined" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[10] "AT+CGMI ↵" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[18] "+CGMI: "Fibocom"↵" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[2] "↵" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[10] "AT+CGMM ↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[38] "+CGMM: "GSM850/900/1800/1900","G510"↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[2] "↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:18node: parseModelIDfunction : (error) "TypeError: Cannot read property 'trim' of undefined"Regards
-
@unix I haven't the possibility to debug it right now, as your debug shows the commands are correctly received, I think you have to change the serial in-out configuration. Check it and send me a screenshot of both.
Also try to put a debug node after join node wired with serial-out
-
@roberts_lando
i have found one error in another flow i have running sms sender i have delete this and the error seems only the trim see screenshots.1

2
3
Regards
i have check the modem connect over cu and modem works and i disconnect to the modem.
-
@unix ok I have found the problem: replace
\nwith\r\nin bothserial-inandserial-outnodes than it should work correctly! This has happen because when you have imported the flow I think you haven't already installed node-red-node-serial and the configuration got lost -
-
@unix you welcome! :)
-
@roberts_lando said in S103-G use GSM/GPRS module to connect to internet:
Hi!
Great tutorial!
I use Raspbian Stretch Lite and I can not get the S103-G to work with these instructions. The command cu -l / dev / ttyAMA0 crashes when I try to AT command. Ifconfig does not give ppp0.
What have I missed?
Vesa
-
@Vesa-Kauppinen
Hi
have you disable the BT on Pi3/boot/config.txt addline
dtoverlay=pi3-disable-btand on /boot/cmdline.txt remove
serial console than its looks like
dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=e13fdf55-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwaitRegards
-
-
I always had compatibility problems when using Raspbian Stretch, try to use last Raspbian Jessie img and it should work
-
Thank you for answer!
Now i have tried with Rasbian Jessie Lite.....no success :disappointed:
Do you use Jessie Lite or full?
Thanks,
Vesa -
@Vesa-Kauppinen I think you have missed one or more step of the turorial. I suggest you to retry the tutorial and check if an instruction fails. Do you have switch on the GPRS module?
-
@roberts_lando Hi, I've done all the steps to configure the internet connection but when I type "ifconfig" it doesn't show me the ppp0 interface. Could you please help me?
when I type the command "cat /var/log/syslog" It show me this messages:
Sep 4 13:41:52 raspberrypi pppd[1698]: pppd 2.4.7 started by root, uid 0
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (BUSY)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (VOICE)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO CARRIER)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO DIALTONE)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO DIAL TONE)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO ANSWER)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (DELAYED)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (ERROR)
Sep 4 13:41:52 raspberrypi chat[1702]: abort on (+CGATT: 0)
Sep 4 13:41:52 raspberrypi chat[1702]: send (AT^M)
Sep 4 13:41:52 raspberrypi chat[1702]: timeout set to 12 seconds
Sep 4 13:41:52 raspberrypi chat[1702]: expect (OK)
Sep 4 13:42:04 raspberrypi chat[1702]: alarm
Sep 4 13:42:04 raspberrypi chat[1702]: Failed
Sep 4 13:42:04 raspberrypi pppd[1698]: Connect script failed
Sep 4 13:42:10 raspberrypi OWFS[477]: DEFAULT: ow_reconnect.c:(72) DS2482-100 bus master reconnected
Sep 4 13:42:30 raspberrypi OWFS[477]: DEFAULT: ow_reconnect.c:(72) DS2482-100 bus master reconnected -
The issue was by the incorrect comm speed with the modem. I modified the guide provided by @roberts_lando to use the proper baudrate of 9600 instead of 115200.
Hello! It looks like you're interested in this conversation, but you don't have an account yet.
Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.
With your input, this post could be even better 💗
Register Login