• Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Search
    • Register
    • Login

    S103-G use GSM/GPRS module to connect to internet

    Scheduled Pinned Locked Moved Neuron Series
    29 Posts 6 Posters 22.8k Views 2 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • roberts_landoR
      roberts_lando @unix
      last edited by roberts_lando

      @unix ok I have found the problem: replace \n with \r\n in both serial-in and serial-out nodes than it should work correctly! This has happen because when you have imported the flow I think you haven't already installed node-red-node-serial and the configuration got lost

      U 1 Reply Last reply
      Reply Quote 0
      • U
        unix @roberts_lando
        last edited by

        @roberts_lando

        WTF great thx for fast response and help :smile:

        regards

        roberts_landoR 1 Reply Last reply
        Reply Quote 0
        • roberts_landoR
          roberts_lando @unix
          last edited by

          @unix you welcome! :)

          1 Reply Last reply
          Reply Quote 0
          • Vesa KauppinenV
            Vesa Kauppinen @roberts_lando
            last edited by

            @roberts_lando said in S103-G use GSM/GPRS module to connect to internet:

            Hi!

            Great tutorial!

            I use Raspbian Stretch Lite and I can not get the S103-G to work with these instructions. The command cu -l / dev / ttyAMA0 crashes when I try to AT command. Ifconfig does not give ppp0.

            What have I missed?

            Vesa

            U 1 Reply Last reply
            Reply Quote 0
            • U
              unix @Vesa Kauppinen
              last edited by

              @Vesa-Kauppinen
              Hi
              have you disable the BT on Pi3

              /boot/config.txt addline

              dtoverlay=pi3-disable-bt
              

              and on /boot/cmdline.txt remove

              serial console than its looks like

              dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=e13fdf55-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
              

              Regards

              Vesa KauppinenV 1 Reply Last reply
              Reply Quote 0
              • Vesa KauppinenV
                Vesa Kauppinen @unix
                last edited by

                @unix

                Thank you for answer!

                BT disabled and cmdline.txt edited...

                No success

                @tomas_hora any ideas?

                Vesa

                1 Reply Last reply
                Reply Quote 0
                • roberts_landoR
                  roberts_lando
                  last edited by

                  I always had compatibility problems when using Raspbian Stretch, try to use last Raspbian Jessie img and it should work

                  Vesa KauppinenV 1 Reply Last reply
                  Reply Quote 0
                  • Vesa KauppinenV
                    Vesa Kauppinen @roberts_lando
                    last edited by Vesa Kauppinen

                    @roberts_lando

                    Thank you for answer!

                    Now i have tried with Rasbian Jessie Lite.....no success :disappointed:

                    Do you use Jessie Lite or full?

                    Thanks,
                    Vesa

                    roberts_landoR 1 Reply Last reply
                    Reply Quote 0
                    • roberts_landoR
                      roberts_lando @Vesa Kauppinen
                      last edited by

                      @Vesa-Kauppinen I think you have missed one or more step of the turorial. I suggest you to retry the tutorial and check if an instruction fails. Do you have switch on the GPRS module?

                      1 Reply Last reply
                      Reply Quote 0
                      • M
                        mattia98 @roberts_lando
                        last edited by mattia98

                        @roberts_lando Hi, I've done all the steps to configure the internet connection but when I type "ifconfig" it doesn't show me the ppp0 interface. Could you please help me?

                        when I type the command "cat /var/log/syslog" It show me this messages:

                        Sep 4 13:41:52 raspberrypi pppd[1698]: pppd 2.4.7 started by root, uid 0
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (BUSY)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (VOICE)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO CARRIER)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO DIALTONE)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO DIAL TONE)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (NO ANSWER)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (DELAYED)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (ERROR)
                        Sep 4 13:41:52 raspberrypi chat[1702]: abort on (+CGATT: 0)
                        Sep 4 13:41:52 raspberrypi chat[1702]: send (AT^M)
                        Sep 4 13:41:52 raspberrypi chat[1702]: timeout set to 12 seconds
                        Sep 4 13:41:52 raspberrypi chat[1702]: expect (OK)
                        Sep 4 13:42:04 raspberrypi chat[1702]: alarm
                        Sep 4 13:42:04 raspberrypi chat[1702]: Failed
                        Sep 4 13:42:04 raspberrypi pppd[1698]: Connect script failed
                        Sep 4 13:42:10 raspberrypi OWFS[477]: DEFAULT: ow_reconnect.c:(72) DS2482-100 bus master reconnected
                        Sep 4 13:42:30 raspberrypi OWFS[477]: DEFAULT: ow_reconnect.c:(72) DS2482-100 bus master reconnected

                        1 Reply Last reply
                        Reply Quote 0
                        • T
                          tomas_hora administrators
                          last edited by

                          The issue was by the incorrect comm speed with the modem. I modified the guide provided by @roberts_lando to use the proper baudrate of 9600 instead of 115200.

                          1 Reply Last reply
                          Reply Quote 0

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better 💗

                          Register Login
                          • First post
                            Last post