• Wireless AP / UnipiAP function

    Official API - Evok
    2
    0 Votes
    2 Posts
    2k Views
    A
    Hi @domguard, The mentioned problems should not be related to EVOK at all. It's not clear from your description what kind of controller you have or what you actually need. Do you need to connect to an existing WiFi, or do you want to create a WiFi access point from the controller? But EVOK works normally, right? Best regards, Antonin, Unipi team
  • Neuron vs Patron long term choice

    Neuron Series
    2
    0 Votes
    2 Posts
    1k Views
    Z
    @arolli Hello Antonio, depends on what the project is. Neuron is cheaper and more suitable for smart home/home automation projects. Patron line is more expensive, but is built to full industrial standards. As for longevity I definitely recommend Patron, in case you decide to use Neuron longevity mainly depends on used SD card, check our eshop for SLC uSD cards, they help a lot.
  • Modbus RTU z TČ PZP Dynamic

    Mervis
    2
    0 Votes
    2 Posts
    961 Views
    B
    @Beny44 Edit: TČ používá PLC Carel, kde bych se měl přes BMS2 linku propojit s Gate. Bohužel jde komunikace jen z Gate, zpět nic. Nastavení jako rychlost a adresu zařízení mám dobře. Našel jsem že i Domat má integraci Carla, viz. https://www.domat-int.com/cs/integrace-carel-modbus
  • 0 Votes
    3 Posts
    2k Views
    T
    @martin_triska Thanks a lot! I had to do some debugging due to incompatible base source deviceTree (which was ultimately resolved by patching the compatible directives and a bit of merging together), but your response helped a ton! It works like a charm, so again, thanks! We plan to open source parts of the project in the future as well (along with a stable release) ... so hopefully it will help someone else too :)
  • 0 Votes
    2 Posts
    872 Views
    M
    Sometimes writing stuff down helps with thinking. The error message is confusing, but I had forgotten to update the vlistfile after making changes to the variable definitions in Mervis. It now works with integers. Seems to still have problems with strings though, is this a limitation?
  • How to update NODE.js, NPM and NodeRed?

    Node-RED
    5
    1 Votes
    5 Posts
    4k Views
    N
    OK I have sorted the partition issue thanks to UniPi tech support: manually resizing the SD card partition using gparted on another Linux system. However I'm still looking for a guide to the 'official' way to upgrade nodeJS, npm and NodeRed on a UniPi Neuron. I'd like nodeJS 18 and Node-RED 3 if possible. The only documentation I came across regarded nodeJS 14 as 'new'!
  • Home assistant integration

    Installations, Ideas & Realisations
    10
    3 Votes
    10 Posts
    8k Views
    J
    @marko2276 , After using your implementation for more than 2 years without flaw, both of my Unipi V1.1 systems (one with my whole Homeassistant installation) "died" from repeating powerfailures, due to grid loss and active but non functional emergency power. Both USB-sticks were damaged with backups on the same stick. Really bad luck, I should have known better. This forced me to a new installation using your altered code with unique_ids. Unfortunately, this code does not work properly having more than one Unipi-device with the same configuration(s). In this case the "unique_ids" will be identical for e.g. lights or switches on Unipi unit 1 and Unipi unit 2! Thus, Homeassistant isn't able to determine the targets anymore and will disable them. It took me some time effort to find this issue. As I'm using UniPi V1.1 devices, this migth only appear within my setup, but I'm pretty sure, this error will also occure on other unipi devices. I managed to get around this issue by extending the unique_id property definition(s) like this: code_text @property def unique_id(self): """Return the unique ID of this light entity.""" return f"{self._device}_{self._port}_at_{self._unipi_hub._name}" Hope, this will help others with the same issue. Cheers, Joerg
  • 1-wire occasionally stops working

    Other Peripherals
    7
    0 Votes
    7 Posts
    3k Views
    P
    @AVsetula I'm aware of this guide and about the OW_off_1 switch. The problem is, that it does not solve the problem in my case. As I wrote before I tried to set OW_off_1 to true and then back to false, but all the temperature sensors kept showing 0 ˚C. I haven't found any software way how to "restart" the 1W to working state. The only thing which works is restarting whole Neuron by cutting off the power. If you have any other ideas, I'll appreciate them.
  • GadgetType 'Analog Meter' isn't supported.

    Mervis
    1
    0 Votes
    1 Posts
    646 Views
    No one has replied
  • HMI and "no connection" with variables

    Mervis
    3
    0 Votes
    3 Posts
    914 Views
    R
    Nobody who knows how to resolve this matter? It doesn't seem to be possible to get any value in the HMI Web. I always get no values and the values.cgi responds with {"ver":1.0,"code":"error","msg":"No variables from request available. Check device parameters and availability."}
  • CM4 + nvme SSD + unipi 1.1 + node red image bootup error

    Node-RED
    3
    0 Votes
    3 Posts
    2k Views
    A
    Hello PEPITO82, The RPi CM4 is currently not an officially supported platform. However, according to my information, should be mostly compatible with "standard" RPi. One option may be to use the RaspberryPi OS image and install the necessary components: EVOK, Node-RED. If you also want so-called Unipi nodes for communication with inputs and outputs, which are available in our Node-RED OS image, just add a suitable module from the palette to Node-RED. Best regards, Antonin
  • 0 Votes
    1 Posts
    1k Views
    No one has replied
  • Analog Input resistance sensor

    Neuron Series
    1
    0 Votes
    1 Posts
    801 Views
    No one has replied
  • UNIPI Modbus TCP

    Node-RED
    1
    0 Votes
    1 Posts
    874 Views
    No one has replied
  • Bullseye and evok running?

    Official API - Evok
    7
    0 Votes
    7 Posts
    3k Views
    N
    Is Evok 2.4.24 fully compatible with Bullseye? I have one RPI with headless Bullseye and on that one everything seems to work. I have another RPI with Bullseye and Lightdm on top and on that one relay state change with JSON POST does not work. Example: POST http://localhost:8080/json/relay/1 Content-Type: application/json { "value": "1" } Result: HTTP/1.1 200 OK Content-Length: 44 Access-Control-Allow-Methods: POST, GET, OPTIONS Server: TornadoServer/4.5.3 Date: Wed, 15 Feb 2023 09:48:09 GMT Access-Control-Allow-Origin: * Access-Control-Allow-Headers: x-requested-with Content-Type: application/json; charset=UTF-8 { "status": "success", "data": { "result": 0 } } The result is "0" and the relay is not switching. Any idea? Best regards, Noël Vaes
  • Import historie.

    Mervis
    1
    1
    0 Votes
    1 Posts
    634 Views
    No one has replied
  • Modbus Registers for UniPi 1.1

    CODESYS
    4
    0 Votes
    4 Posts
    2k Views
    U
    @Martin-Kudláček Hi After a long time of trying and many tutorials, I made it to switch my relays on my Unipi 1.1, to read temperatures and everything with ModbusTCP and Nodered. When I see it now, it's very easy, thank you for the great board and the software.
  • node red istance to be interfaced to Mervis PLC

    Node-RED
    7
    0 Votes
    7 Posts
    3k Views
    U
    Hallo Ich habe bei mir ein unipi 1.1 bekomme auch Information von mervis zurück ,jetzt meine Frage ,wieviel Modbus Knoten kann ich in node red einbringen. Ich habe 3 Stück, bei den die Verbindung unterbricht Was mache ich falsch Dankeschön für eure Antwort Udo
  • 0 Votes
    2 Posts
    1k Views
    A
    I see now that these are included in neuron-main tree, but it was never installed on my rpi because the install script failed. The following packages have unmet dependencies: unipi-kernel-modules : Depends: raspberrypi-kernel (= 1:1.20221104-1) but 1:1.20230106-1 is to be installed E: Unable to correct problems, you have held broken packages. Cleaning temporary files Cleaning temporary files I am guessing you need a better way of determining the platform, otherwise this is going to break each time a new rpi kernel is released before you have a chance to build the modules package... If anyone needs a workaround, install like this: wget -qO - https://repo.unipi.technology/debian/raspberry-install.sh | sed s/unipi-kernel-modules/unipi-kernel-modules-dkms/ | bash
  • RS485 to external Modbus RTU board

    Other Peripherals
    1
    0 Votes
    1 Posts
    1k Views
    No one has replied