• bug: cacert-update.service

    Mervis
    1
    0 Votes
    1 Posts
    173 Views
    No one has replied
  • 0 Votes
    1 Posts
    267 Views
    No one has replied
  • připojení mervis k home assistant?

    Mervis
    3
    0 Votes
    3 Posts
    1k Views
    L
    Tato integrace je brutálně omezená, hodí se jen pro malé sady proměnných které se všechny týkají jedné věci. Nelze například světla rozdělit do více místností. Naučil jsem se raději jak to přenášet modbusem.
  • Neuron L203 not booting, led flashing, bricked ?

    Neuron Series
    2
    0 Votes
    2 Posts
    362 Views
    C
    Hello, if you wish to send us the unit for repair (if you suspect HW damage), you can read terms and fill out our form. Otherwise can you show me picture of the LEDs to see their exact state?
  • Upgrading old firmware on Neuron M103

    Neuron Series
    6
    0 Votes
    6 Posts
    1k Views
    C
    Hello @ntd, there should be no stability issues with the old firmware, some features might be absent and there may be some bugs, but if you test it and it works fine, it should be okay.
  • Mervis on Neuron: web does not refresh data

    Mervis
    1
    0 Votes
    1 Posts
    537 Views
    No one has replied
  • Config file for using one Mervis solution on mulitple PLCs

    Mervis
    2
    0 Votes
    2 Posts
    726 Views
    U
    Using different profiles for each PLC partially solves this, as they store the PLC properties and configuration. But they don't store everything, for example the terminal settings (SCADA Terminal parameters, PLC History profile). So currently I have to change the terminal settings manually. I suppose there's a better way to do it with multiple terminals, but I struggled to get this to work.
  • Odesílání e-mailů - SendMailTrig

    Mervis
    2
    0 Votes
    2 Posts
    881 Views
    O
    Dobrý den, ten result, u toho bloku se mění jen když je špatně uveděný kanál, plná emailová fronta nebo interní chyba. Pokud Vás zajímá zda se spojení opravdu navazuje, tak při připojení přes SSH lze monitorovat připojení nástrojem netstat. V tomto případě lze sledovat spojení takto: netstat -natc | grep 465 Zkuste se podívat zda není na začátku nebo na konci hesla, uživatelském jména, adresy nebo portu nějaký neviditelný znak (např. mezera)
  • 0 Votes
    3 Posts
    935 Views
    S
    @cleve Hello Cleve Thanks for reply. sudo apt-get -o Dpkg::Options::="--force-confmiss" install --reinstall evok-unipi-data Did what it was supposed to do. Thank a lot for your help.
  • modbus registry High Word a Low_Word nejsou za sebou

    Mervis
    4
    0 Votes
    4 Posts
    1k Views
    C
    Dobrý den, @tomasmedek příklad nemáme, takto specifická věc není součástí standardní neplacené podpory.
  • read 1W-TH-IB2 values by HTTP/HTTPS or modbus TCP-IP

    Axon series
    7
    0 Votes
    7 Posts
    2k Views
    C
    Hello @Bart-Delaere, unfortunately there is no definitive answer. The 1-Wire bus is technically able to connect huge amount of devices, but reality depends on cable length, quality, noise from the environment etc, so this may be trial and error for users that do not install it daily. Unipi used to sell a hub/splitter, which we do not offer anymore. Sometimes, a surge can occur in the environment, which can take down the whole bus. Unipi units (except Unipi 1/Lite) have an option to restart the bus (the bus is not restarted during normal system reboot), you can look in the Modbus table of your unit if you wish to implement it.
  • Issues finding the correct block

    Mervis axon
    3
    0 Votes
    3 Posts
    2k Views
    Bart DelaereB
    Is nobody using the Analog output (0-10V) to dim LED lights?
  • 0 Votes
    3 Posts
    3k Views
    K
    @cleve Thanks for letting me know. To be honest- there is no urgent need for upgrading. I just prefer to be on the up-to-date version knowing the old stable gets outdated faser than expected ;) Do you have an estimation when it might be available for Trixie? Thanks! /KNEBB
  • Image with Node-RED for Patron with Debian 12 (Bookworm)

    Node-RED
    15
    0 Votes
    15 Posts
    8k Views
    C
    Hello @lukas009, we plan to release Debian 13 based systems, but we do not have any ETA.
  • .gitignore recommendations for Mervis projects

    Mervis
    1
    2 Votes
    1 Posts
    1k Views
    No one has replied
  • Modifikace proměnné ze dvou míst

    Mervis
    2
    1
    0 Votes
    2 Posts
    1k Views
    L
    Tak write on change dělá přesně to co potřebuji. Proměnnou lze modifikovat z druhého místa, ale sesynchronizuje se zpět, když se změní stav logiky v FBD. Píšu pro případ, kdyby se to někomu také hodilo, protože v dokumentaci o tom není ani píp.
  • 0 Votes
    1 Posts
    1k Views
    No one has replied
  • Unipi 1.1 Analog Inputs

    Unipi 1 - First Generation
    1
    1
    0 Votes
    1 Posts
    599 Views
    No one has replied
  • HMI problem

    Mervis mervis mervis hmi hmi
    4
    0 Votes
    4 Posts
    3k Views
    I
    Found the mistake. It was in PLC settings - Web Parameters, wrong Definition Directory.
  • 0 Votes
    3 Posts
    2k Views
    A
    @cleve Because I never use precompiled modules on debian based systems if I can help it since dkms was introduced in the '00s, I like the flexibility of not having to match kernels with specific precompiled modules. For example, right now on one of my systems: unipi-kernel-modules : Depends: linux-image-rpi-v8 (= 1:6.12.20-1+rpt1~bpo12+1) but 1:6.6.74-1+rpt1 is to be installed I have multiple rpi3 and rpi4 based neuron systems that I maintain, most are runing raspberry pi os bookworm aarch64. BTW unipi-kernel-modules-dkms=2.70~bookworm builds just fine until at least linux-image-6.6.74+rpt-rpi-v8