• Neuron L203 not booting, led flashing, bricked ?

    2
    0 Votes
    2 Posts
    362 Views
    C
    Hello, if you wish to send us the unit for repair (if you suspect HW damage), you can read terms and fill out our form. Otherwise can you show me picture of the LEDs to see their exact state?
  • Upgrading old firmware on Neuron M103

    6
    0 Votes
    6 Posts
    1k Views
    C
    Hello @ntd, there should be no stability issues with the old firmware, some features might be absent and there may be some bugs, but if you test it and it works fine, it should be okay.
  • Analogue Input Type not correct?

    3
    1
    0 Votes
    3 Posts
    2k Views
    K
    @cleve Neuron M103 (the old one, not the current) which is still running with Raspbian 10/ buster. How do I get the information about the firmware? (BTW: I tried to upgrade to latest Raspbian, but failed)
  • Re-Calculation of Voltage for AI/AO still valid?

    2
    0 Votes
    2 Posts
    2k Views
    C
    Hello @knebb, we do not provide support for Buster based systems anymore. However, on the latest firmware with BaseOS 12, the value is the actual value (the datatype is real - float32), there is no further calculation needed.
  • Modbus Sx40, zapínání relé, node red

    2
    1
    0 Votes
    2 Posts
    1k Views
    C
    Dobrý den @SorakCz, doporučil bych zařízení vyčítat přes Evok, v tom případě k němu budete přistupovat stejně jako k IO na jednotce, odkaz do dokumentace. Pokud si to nepřejete, mapy registrů Modbus naleznete na našem KB.
  • Controlling FAN 0-10V - wiring needed

    2
    1
    0 Votes
    2 Posts
    2k Views
    K
    Replying to mysqlf as I found a nice guy who did the cabling for me. As I want to control two vents the wiring has been extended accordingly: [image: a4ab227e-bcae-4181-a2bc-968b0c0611af-grafik.png] So for each vent I need a 47k resistor and a 12V diode. That's it! Easy for someone who knowns. Impossible to do it for me. /KNEBB
  • PWM Example on DigOut

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • Cannot uprgrading firmware

    5
    0 Votes
    5 Posts
    2k Views
    P
    Thank you @cleve It works with unipi@L203-sn121:~$ sudo /opt/unipi/tools/fwspi -u 1 -P -U unipi@L203-sn121:~$ sudo /opt/unipi/tools/fwspi -u 2 -P -U unipi@L203-sn121:~$ sudo /opt/unipi/tools/fwspi -u 3 -P -U
  • Output turning off after a few seconds

    4
    0 Votes
    4 Posts
    2k Views
    C
    Hello @oversc0re, it is very likely as you say, inrush current burnt the relay, you may use external one or some protection to prevent this in future.
  • Errors in the sysfs documentation

    4
    0 Votes
    4 Posts
    2k Views
    C
    @paolo Right, I did not notice the 0, the commands are just examples and it's possible to list the files in the directory, but I will correct that.
  • How to configure wlan0

    4
    0 Votes
    4 Posts
    2k Views
    C
    @riccardooo Hello, it would be better if you create a separate thread for an unrelated issue next time. Our systems use systemd-networkd, it's a standard GNU/Linux daemon, you can refer to Debian/Arch Linux manuals.
  • Bookworm 32 bits NEURON

    2
    0 Votes
    2 Posts
    2k Views
    C
    @gabrielsoudry Hello, the 32 bit images are currently unavailable, because of a bug in 32 bit packages, they should be available soon.
  • Grateful switching NEURON OFF

    2
    0 Votes
    2 Posts
    2k Views
    C
    @iVar Hello, which software/OS do you use on your units?
  • Upgrading to Bullseye?

    17
    0 Votes
    17 Posts
    8k Views
    Z
    @gabrielsoudry Hello Gabriel, We plan to release the new Bookworm-compatible EVOK, along with new OS images, by the end of February. However, if we encounter bugs during testing, this may extend until the end of March. ZR tag @martin_triska
  • Bulleyes Images "posledni-image"

    2
    -1 Votes
    2 Posts
    2k Views
    Z
    Hello Gabriel, this page should not be publicly available, thanks a lot for letting us know 😅 as for your question, these images are for testing only, so no guarantees of stability.
  • Neuron vs Patron long term choice

    2
    0 Votes
    2 Posts
    1k Views
    Z
    @arolli Hello Antonio, depends on what the project is. Neuron is cheaper and more suitable for smart home/home automation projects. Patron line is more expensive, but is built to full industrial standards. As for longevity I definitely recommend Patron, in case you decide to use Neuron longevity mainly depends on used SD card, check our eshop for SLC uSD cards, they help a lot.
  • Analog Input resistance sensor

    1
    0 Votes
    1 Posts
    801 Views
    No one has replied
  • Neuron Older Models M20x

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • How to use Watchdog?

    1
    0 Votes
    1 Posts
    1k Views
    No one has replied
  • SD Card problem

    7
    0 Votes
    7 Posts
    3k Views
    A
    Hi everyone, In the current version of Mervis OS 2.4.2.4, writes to the card already occur at least, according to the set interval for storing retain variables. For a similar reason, the history is newly stored in RAM (data is lost after the power is disconnected or restarted), which does not matter in combination with the cloud-based Mervis DB. If you disable writes to the internal storage (SD card), there are two possibilities of what can happen (depending on how you disable the writes): Mervis RT always unlocks the storage when writing retain variables, writes and locks the storage again for writing (basically the same behavior as now) Storage will be permanently locked and retain variables will not be writable. Likewise, it will not be possible to upload a new assembly (program) from Mervis IDE. In general, I recommend purchasing an SLC card with a longer lifespan and resistance to random power outages, etc., for the operation of the controller. You can read more about this issue in this article. Best regards, Antonin, Unipi