• 1-wire bus topology

    5
    0 Votes
    5 Posts
    4k Views
    T
    We do not minimize the total length of the DQ line but we rather have a little longer (twice) total topology weight and minimize the distance of the stubs to achieve linear topology. So the length of the stub is about 1cm max. https://www.maximintegrated.com/en/app-notes/index.mvp/id/148
  • smart home solution

    7
    0 Votes
    7 Posts
    5k Views
    N
    thanks for quick answer and guidance After fast look into documentation, I have found that for all DI for external power source I have to switch all JP2 to JP5 to label side
  • Single Power Source Problems

    13
    0 Votes
    13 Posts
    8k Views
    M
    JP1 has been mounted, sorry was faulty information. But finaly i found the problem: 5V GND was not connected to the UniPI power plug, only on the mini USB. Thank's for you help. best regards Michael
  • MCP7491x Jessie

    3
    0 Votes
    3 Posts
    3k Views
    D
    I had made a mistake and the notes on the wiki do work for me (I found I didn't need the entry in /etc/modules though). Anyway an updated script that works for me on a clean install of Jessie is below #!/bin/bash # UniPi driver setup if [ "$EUID" -ne 0 ] then echo "This script must be run as root" exit fi echo Backup files cp /boot/config.txt /boot/config.txt.bak echo Enabling I2C bus... if ! grep -q '^dtparam=i2c_arm=on' /boot/config.txt then echo 'dtparam=i2c_arm=on' >> /boot/config.txt fi if ! grep -q '^dtparam=i2c_baudrate=400000' /boot/config.txt then echo 'dtparam=i2c_baudrate=400000' >> /boot/config.txt fi echo Enabling the RTC chip... if ! grep -q '^dtoverlay=i2c-rtc,mcp7941x' /boot/config.txt then echo 'dtoverlay=i2c-rtc,mcp7941x' >> /boot/config.txt fi echo Getting i2c development tools apt-get install -y i2c-tools if ! grep -q '^i2c-dev' /etc/modules then echo 'i2c-dev' >> /etc/modules fi echo Removing fake-hwclock... apt-get purge -y fake-hwclock update-rc.d -f fake-hwclock remove apt-get autoremove -y sed -i '/^if \[ -e \/run\/systemd\/system/,/^fi/s/^/#/' /lib/udev/hwclock-set echo ' ' echo 'UniPi installed.' echo ' ' echo '!!! REBOOT IS REQUIRED !!!' echo ' ' read -p "Is it OK to reboot now? [y/N] " -n 1 -r echo ' ' if [[ $REPLY =~ ^[Yy]$ ]] then reboot else echo 'Reboot to finish configuring drivers' fi echo ' '
  • Digital input 2 stays closed

    6
    0 Votes
    6 Posts
    3k Views
    T
    You are right, pilight was still running ! [image: :)] Thank you
  • False digital input

    4
    0 Votes
    4 Posts
    3k Views
    E
    Thank you. Sorry apparently I didn't search well enough on my topic. I'll continue this thread over there.
  • Electric potential

    3
    0 Votes
    3 Posts
    2k Views
    ?
    Using different PSU is described in technical documentation, see https://files.unipi.technology/index.ph ... niPi%201.1 Depending on what DI you want to use with the other PSU you will have to switch JP2 and JP3 at minimum.
  • 24V AC Input

    4
    0 Votes
    4 Posts
    3k Views
    C
    I thought of bridge rectifier, but I would need 8 of them. I found a gang of eight 24vac relays about the size of the ones on the UniPi, but I didn't think that was elegant and power efficient.
  • Switching lights and led drivers

    3
    0 Votes
    3 Posts
    2k Views
    ?
    Hello, solid state relays are ideal for switching LED lights, see the datasheets below for more information. If you use adequate cooling for the load it will withstand for years. I would not much bother with the minimal load, but check the datasheet. Yest SSRs are great because of switching at zero. http://www.sharp-world.com/products/dev ... 2s02_e.pdf https://www.omron.com/ecb/products/pdf/en-g5q.pdf
  • 1-Wire Hub. Distance to Unipi board

    4
    0 Votes
    4 Posts
    3k Views
    T
    Ok Many thanks
  • undefined

    null
    -3
    0 Votes
    -3 Posts
    0 Views
    No one has replied
  • undefined

    null
    -1
    0 Votes
    -1 Posts
    0 Views
    No one has replied
  • UniPi digital input

    3
    0 Votes
    3 Posts
    3k Views
    ?
    Hello Chris, the inputs are designed to work in the range of 5-24V DC. This means you can use both. But the 5V cannot guarantee 100% working on long cables because of voltage drop. So I suggest using the internal 12V. (The third option is using external 12-24V power supply)
  • Analog Output

    5
    0 Votes
    5 Posts
    4k Views
    ?
    Hello, I have created a simple wiki page. See http://unipi.technology/wiki/Using_Analog_Output Let me know if anything is missing or not clear and I will fix it.