S103-G use GSM/GPRS module to connect to internet
-
@roberts_lando Great! Thanks a lot!
-
@tomas_hora Just made a node-red Dashboard to get Modem Data :)
With MNC MCC CellID and LAC it is also possible to get the location of the device by using https://opencellid.org/ APIs
-
Re: S103-G use GSM/GPRS module to connect to internet
Does anyone know if it's possible to send AT commands from Mervis after turning on the modem first? Thanks.
-
@oho Support of the GSM functionality will be available in Mervis in the next release.
-
@roberts_lando hi iam new in node-red and S103-g my question is can you share your nice looking flow to learn better node-red.
regards -
@unix I have added it to node-red flows library: https://flows.nodered.org/flow/af6487676bd89e5e8b74b2c9da1e176d
Enjoy :)
-
Nice thx for help :smile:
Regards -
Hi
i have inport your data but i get one error in debug
its "3.11.2017, 10:59:29node: parseModelIDfunction : (error)
"TypeError: Cannot read property 'trim' of undefined""and the website looks like :
connect is green but no info i have only change the serial connect to
/dev/ttyAMA0: 115200-8n1or i have problems whit the modem i can send the first sms whitout problems but after this only error when i test it whit cu -l /dev/ttyAMA0
hope for hints :smile:
Regards
-
@unix Did you close the connection after using cu? Cause that error means that I call .trim() in an undefined var (modelID) that means no data is received after the command. Each command has a timeout, after that I close the read stream from the serial and I try to parse the response string, if the response string is not well parsed those errors are normal, try to put a debug node to see the output of the serial and check that the cu session is closed.
Disconnect: type ~ (alt+126) than wait for [unipi] output than type . and hit <Enter>
-
Hi
yes the cu session a closed in debug i see this3.11.2017, 11:25:11node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[11] "AT+COPS? ↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[17] "+COPS: 0,0,"A1"↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[2] "↵" 3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:14node: parseOperatorfunction : (error) "TypeError: Cannot read property 'trim' of undefined" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[10] "AT+CGMI ↵" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[18] "+CGMI: "Fibocom"↵" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[2] "↵" 3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[10] "AT+CGMM ↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[38] "+CGMM: "GSM850/900/1800/1900","G510"↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[2] "↵" 3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[4] "OK↵" 3.11.2017, 11:25:18node: parseModelIDfunction : (error) "TypeError: Cannot read property 'trim' of undefined"
Regards
-
@unix I haven't the possibility to debug it right now, as your debug shows the commands are correctly received, I think you have to change the serial in-out configuration. Check it and send me a screenshot of both.
Also try to put a debug node after join node wired with serial-out
-
@roberts_lando
i have found one error in another flow i have running sms sender i have delete this and the error seems only the trim see screenshots.1
2
3Regards
i have check the modem connect over cu and modem works and i disconnect to the modem.
-
@unix ok I have found the problem: replace
\n
with\r\n
in bothserial-in
andserial-out
nodes than it should work correctly! This has happen because when you have imported the flow I think you haven't already installed node-red-node-serial and the configuration got lost -
-
@unix you welcome! :)
-
@roberts_lando said in S103-G use GSM/GPRS module to connect to internet:
Hi!
Great tutorial!
I use Raspbian Stretch Lite and I can not get the S103-G to work with these instructions. The command cu -l / dev / ttyAMA0 crashes when I try to AT command. Ifconfig does not give ppp0.
What have I missed?
Vesa
-
@Vesa-Kauppinen
Hi
have you disable the BT on Pi3/boot/config.txt addline
dtoverlay=pi3-disable-bt
and on /boot/cmdline.txt remove
serial console than its looks like
dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=e13fdf55-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
Regards
-
-
I always had compatibility problems when using Raspbian Stretch, try to use last Raspbian Jessie img and it should work
-
Thank you for answer!
Now i have tried with Rasbian Jessie Lite.....no success :disappointed:
Do you use Jessie Lite or full?
Thanks,
Vesa