• Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Search
    • Register
    • Login

    S103-G use GSM/GPRS module to connect to internet

    Scheduled Pinned Locked Moved Neuron Series
    29 Posts 6 Posters 22.8k Views 2 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • T
      tomas_hora administrators @roberts_lando
      last edited by

      @roberts_lando You got the wrong tutorial, try eg this one: http://www.rhydolabz.com/wiki/?p=16325

      1 Reply Last reply
      Reply Quote 0
      • roberts_landoR
        roberts_lando
        last edited by

        Thanks @tomas_hora I did it now! If you want I can make a full tutorial about this topic

        1 Reply Last reply
        Reply Quote 0
        • roberts_landoR
          roberts_lando
          last edited by tomas_hora

          TUTORIAL FIBOCOM G510 Unipi Neuron S103-G

          Make the file-system writable:

          mount / -o remount,rw
          mount /boot -o remount,rw
          

          Test the interface /dev/ttyAMA0 (serial link parameters: 115 200 1N8 Bps/Par/Bits)

          1. Export pin 18
          echo 18 >/sys/class/gpio/export
          
          1. Switch on module
          echo out > /sys/class/gpio/gpio18/direction
          echo 1 > /sys/class/gpio/gpio18/value
          echo 0 > /sys/class/gpio/gpio18/value
          sleep 1
          echo 1 > /sys/class/gpio/gpio18/value
          sleep 2
          
          1. Start the communication using cu
          apt-get install cu
          chown root:root /dev/ttyAMA0
          cu -l /dev/ttyAMA0
          
          1. Test: send sms (<Enter> means you have to press enter, OK is the output of the command)
          AT  <Enter>
          OK
          
          AT+CMGF=1 <Enter>
          OK
          
          AT+CMGS="yourphonenumber" <Enter>
          > Prova  <Ctrl+z>
          
          +CMGS: 152
          OK
          
          1. Disconnect: type ~ (alt+126) than wait for [unipi] output than type . and hit <Enter>
          ~[unipi]. <Enter>
          

          If interface doesn't works try:

          1. Enable UART: nano /boot/cmdline.txt add (if not present) or edit this line: enable_uart=1. Close and save the file by typing Ctrl+X and Y. Reboot Unipi Neuron and retry to test the interface.

          Now let's configure the interface for internet connection

          1. Install required packages
          apt-get update
          apt-get install ppp screen elinks
          
          1. Edit the configuration file (I use nano apt-get install nano)
          cd /etc/ppp/peers/
          nano rnet
          
          1. Copy the code below to the new file
          #configure for connection
          connect "/usr/sbin/chat -v -f /etc/chatscripts/gprs -T <yourAPNhere>"
           
          # Use /dev/ttyAMA0 as the communication port:
          /dev/ttyAMA0
           
          # Baudrate
          9600
           
          # Assumes that your IP address is allocated dynamically by the ISP.
          noipdefault
           
          # Try to get the name server addresses from the ISP.
          usepeerdns
           
          # Use this connection as the default route to the internet.
          defaultroute
           
          # Makes PPPD "dial again" when the connection is lost.
          persist
           
          # Do not ask the remote to authenticate.
          noauth
           
          # No hardware flow control on the serial link with GSM Modem
          nocrtscts
           
          # No modem control lines with GSM Modem
          local
          
          1. Replace <yourAPNhere> with your APN (Search in google APN of "your mobile operator") close and save the file by typing Ctrl+X and Y

          2. If your SIM card has a PIN edit this file nano /etc/chatscripts/gprs un comment the line AT+CPIN=1234 and set the pin instead of 1234

          3. Enable the connection by typing pon rnet. The show the log for PPPD type cat /var/log/syslog | grep pppd it will show if connection is established successfully.

          4. Type ifconfig, now you should see another interface named ppp0.

          0_1507015540134_upload-6607adf9-72d1-4cc9-97e2-cbe5b291b1c7

          1. To close the connection type poff rnet
          T Vesa KauppinenV M 3 Replies Last reply
          Reply Quote 0
          • T
            tomas_hora administrators @roberts_lando
            last edited by

            @roberts_lando Great! Thanks a lot!

            1 Reply Last reply
            Reply Quote 0
            • roberts_landoR
              roberts_lando
              last edited by roberts_lando

              @tomas_hora Just made a node-red Dashboard to get Modem Data :)

              0_1507124912843_upload-f44d0f00-3612-47f8-aa08-91819d6ff5fe

              0_1507124782319_upload-8a2171eb-31ce-403a-8b88-428e8162c1b4

              With MNC MCC CellID and LAC it is also possible to get the location of the device by using https://opencellid.org/ APIs

              U 1 Reply Last reply
              Reply Quote 0
              • O
                oho
                last edited by

                Re: S103-G use GSM/GPRS module to connect to internet

                Does anyone know if it's possible to send AT commands from Mervis after turning on the modem first? Thanks.

                T 1 Reply Last reply
                Reply Quote 0
                • T
                  tomas_hora administrators @oho
                  last edited by

                  @oho Support of the GSM functionality will be available in Mervis in the next release.

                  1 Reply Last reply
                  Reply Quote 0
                  • U
                    unix @roberts_lando
                    last edited by

                    @roberts_lando hi iam new in node-red and S103-g my question is can you share your nice looking flow to learn better node-red.
                    regards

                    1 Reply Last reply
                    Reply Quote 0
                    • roberts_landoR
                      roberts_lando
                      last edited by roberts_lando

                      @unix I have added it to node-red flows library: https://flows.nodered.org/flow/af6487676bd89e5e8b74b2c9da1e176d

                      Enjoy :)

                      1 Reply Last reply
                      Reply Quote 0
                      • U
                        unix
                        last edited by

                        Nice thx for help :smile:
                        Regards

                        1 Reply Last reply
                        Reply Quote 0
                        • U
                          unix
                          last edited by

                          Hi
                          i have inport your data but i get one error in debug
                          its "3.11.2017, 10:59:29node: parseModelIDfunction : (error)
                          "TypeError: Cannot read property 'trim' of undefined""

                          and the website looks like :
                          Daschboard
                          connect is green but no info i have only change the serial connect to
                          /dev/ttyAMA0: 115200-8n1

                          or i have problems whit the modem i can send the first sms whitout problems but after this only error when i test it whit cu -l /dev/ttyAMA0

                          hope for hints :smile:

                          Regards

                          roberts_landoR 1 Reply Last reply
                          Reply Quote 0
                          • roberts_landoR
                            roberts_lando @unix
                            last edited by roberts_lando

                            @unix Did you close the connection after using cu? Cause that error means that I call .trim() in an undefined var (modelID) that means no data is received after the command. Each command has a timeout, after that I close the read stream from the serial and I try to parse the response string, if the response string is not well parsed those errors are normal, try to put a debug node to see the output of the serial and check that the cu session is closed.

                            Disconnect: type ~ (alt+126) than wait for [unipi] output than type . and hit <Enter>

                            1 Reply Last reply
                            Reply Quote 0
                            • U
                              unix
                              last edited by

                              Hi
                              yes the cu session a closed in debug i see this

                              3.11.2017, 11:25:11node: 96ac4186.358femsg.payload : string[4]
                              "OK↵"
                              3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[11]
                              "AT+COPS? ↵"
                              3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[17]
                              "+COPS: 0,0,"A1"↵"
                              3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[2]
                              "↵"
                              3.11.2017, 11:25:13node: 96ac4186.358femsg.payload : string[4]
                              "OK↵"
                              3.11.2017, 11:25:14node: parseOperatorfunction : (error)
                              "TypeError: Cannot read property 'trim' of undefined"
                              3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[10]
                              "AT+CGMI ↵"
                              3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[18]
                              "+CGMI: "Fibocom"↵"
                              3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[2]
                              "↵"
                              3.11.2017, 11:25:15node: 96ac4186.358femsg.payload : string[4]
                              "OK↵"
                              3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[10]
                              "AT+CGMM ↵"
                              3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[38]
                              "+CGMM: "GSM850/900/1800/1900","G510"↵"
                              3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[2]
                              "↵"
                              3.11.2017, 11:25:17node: 96ac4186.358femsg.payload : string[4]
                              "OK↵"
                              3.11.2017, 11:25:18node: parseModelIDfunction : (error)
                              "TypeError: Cannot read property 'trim' of undefined"
                              

                              Regards

                              roberts_landoR 1 Reply Last reply
                              Reply Quote 0
                              • roberts_landoR
                                roberts_lando @unix
                                last edited by roberts_lando

                                @unix I haven't the possibility to debug it right now, as your debug shows the commands are correctly received, I think you have to change the serial in-out configuration. Check it and send me a screenshot of both.

                                Also try to put a debug node after join node wired with serial-out

                                U 1 Reply Last reply
                                Reply Quote 0
                                • U
                                  unix @roberts_lando
                                  last edited by

                                  @roberts_lando
                                  i have found one error in another flow i have running sms sender i have delete this and the error seems only the trim see screenshots.

                                  1 alt text
                                  2 alt text
                                  3 alt text

                                  Regards

                                  i have check the modem connect over cu and modem works and i disconnect to the modem.

                                  roberts_landoR 1 Reply Last reply
                                  Reply Quote 0
                                  • roberts_landoR
                                    roberts_lando @unix
                                    last edited by roberts_lando

                                    @unix ok I have found the problem: replace \n with \r\n in both serial-in and serial-out nodes than it should work correctly! This has happen because when you have imported the flow I think you haven't already installed node-red-node-serial and the configuration got lost

                                    U 1 Reply Last reply
                                    Reply Quote 0
                                    • U
                                      unix @roberts_lando
                                      last edited by

                                      @roberts_lando

                                      WTF great thx for fast response and help :smile:

                                      regards

                                      roberts_landoR 1 Reply Last reply
                                      Reply Quote 0
                                      • roberts_landoR
                                        roberts_lando @unix
                                        last edited by

                                        @unix you welcome! :)

                                        1 Reply Last reply
                                        Reply Quote 0
                                        • Vesa KauppinenV
                                          Vesa Kauppinen @roberts_lando
                                          last edited by

                                          @roberts_lando said in S103-G use GSM/GPRS module to connect to internet:

                                          Hi!

                                          Great tutorial!

                                          I use Raspbian Stretch Lite and I can not get the S103-G to work with these instructions. The command cu -l / dev / ttyAMA0 crashes when I try to AT command. Ifconfig does not give ppp0.

                                          What have I missed?

                                          Vesa

                                          U 1 Reply Last reply
                                          Reply Quote 0
                                          • U
                                            unix @Vesa Kauppinen
                                            last edited by

                                            @Vesa-Kauppinen
                                            Hi
                                            have you disable the BT on Pi3

                                            /boot/config.txt addline

                                            dtoverlay=pi3-disable-bt
                                            

                                            and on /boot/cmdline.txt remove

                                            serial console than its looks like

                                            dwc_otg.lpm_enable=0 console=tty1 root=PARTUUID=e13fdf55-02 rootfstype=ext4 elevator=deadline fsck.repair=yes rootwait
                                            

                                            Regards

                                            Vesa KauppinenV 1 Reply Last reply
                                            Reply Quote 0

                                            Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                                            Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                                            With your input, this post could be even better 💗

                                            Register Login
                                            • First post
                                              Last post