• Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Search
    • Register
    • Login

    Problem recognition 1w-Wire

    Scheduled Pinned Locked Moved Mervis
    19 Posts 4 Posters 9.8k Views 1 Watching
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • T
      TriathletC @zorro_66
      last edited by TriathletC

      @zorro_66
      thank you

      1 Reply Last reply
      Reply Quote 0
      • T
        TriathletC
        last edited by

        Goodbye to everyone .. I finally finally managed to recognize the 1-Wire basic temperature sensor of the PLC .. it works properly ..
        But now I need a help ..
        I also bought two sensors of the UNICA Wire Sensor (temperature-humidity and light sensor) all in one.
        The problem is how to connect it .. I have two photos to let you know better.
        Virtually I connected to terminal 5 i + 5V, to 6 the DATA, 7 empty, 8 GND.
        I connected it to the Wire port I tried to make the recognition but with a negative result .. I also attach the screen of how I inserted the device in the Mervis..HO performed the same procedure for the 1-Wire sensor ..2_1504170021892_3.JPG 1_1504170021892_2.JPG 0_1504170021891_1.JPG

        T 1 Reply Last reply
        Reply Quote 0
        • T
          tomas_hora administrators @TriathletC
          last edited by

          @TriathletC Please check the pin map of the RJ45: https://www.unipi.technology/hardware_documentation/1-wire-network-46

          The wiring seems OK, but you have to wire at also both data lines to the sensor, or you break the topology.

          Also, do not strip the end of cables when you make the RJ45 connector. The connector cuts the plastic foil of the cable when you press it with the crimping tool. If you strip the cables before, the cables can touch each other which could cause shortcut....

          1 Reply Last reply
          Reply Quote 0
          • T
            TriathletC
            last edited by

            So from what you tell me I have to bring another thread and jump to the DQ. right?

            T 1 Reply Last reply
            Reply Quote 0
            • T
              tomas_hora administrators @TriathletC
              last edited by

              @TriathletC Correct

              T 1 Reply Last reply
              Reply Quote 0
              • T
                TriathletC @tomas_hora
                last edited by

                @tomas_hora
                Thanks Thoma ... you were right I wore everything as you said and it works correctly .. so I need an info .. how do I parameterize the UR%?

                T 1 Reply Last reply
                Reply Quote 0
                • T
                  tomas_hora administrators @TriathletC
                  last edited by

                  @TriathletC You are welcome... But now I do not understand. Could you describe it better please?

                  T 1 Reply Last reply
                  Reply Quote 0
                  • T
                    TriathletC @tomas_hora
                    last edited by

                    @tomas_hora
                    I do not know how to configure correctly so that I can read the relative uimness on the mervis I attach to the screens.1_1504260494139_Cattura_2.JPG 0_1504260494139_Cattura_1.JPG

                    D 1 Reply Last reply
                    Reply Quote 0
                    • D
                      David @TriathletC
                      last edited by

                      @TriathletC Try to use FUPLA block called 'unica_u1wt'.

                      T 1 Reply Last reply
                      Reply Quote 0
                      • T
                        TriathletC @David
                        last edited by

                        @David SO?0_1504266359576_Cattura.JPG

                        1 Reply Last reply
                        Reply Quote 0
                        • D
                          David
                          last edited by

                          Yes, that it should work.

                          1 Reply Last reply
                          Reply Quote 0

                          Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                          Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                          With your input, this post could be even better đź’—

                          Register Login
                          • First post
                            Last post