@tomas_hora
hello, I found a solution to turn a digital setter into push-Button
I put a flip-flop that reset after 2 seconds the variable on which points the digital setter HMI
https://www.dropbox.com/s/dvf4toi76z35kxw/Capture d'écran 2019-01-10 09.56.36.png?dl=0
Best posts made by msoenen
-
RE: HMI update issue
Latest posts made by msoenen
-
Configuration mervi for scada impossible
Hello
I'm trying to configure Mervis to use the scada, but I don't have the same screens as the tutorial (see appendix) could you help me(https://1drv.ms/w/s!Aq__SFpXusxkgcYpxOZEcucrK36pMA?e=gRy2i8) -
RE: SD Card fails after current cut
Hello
Thanks for answer
I will try to make a backup power supply with batteries so as not to have sudden stops
-
SD Card fails after current cut
Hello
for the second time, the program of my L 203 no longer works, and the SD card is out of order, and it happens when there is a power cut. luckily I made a copy of the map. these are good quality cards. do you know the cause? A solution to avoid the problem, with batteries? thank you in advance -
RE: Loss of connection with PLC
Problem solved, I did a complete reinstallation in version 2.2, because version 2.3 does not work for me
thanks
-
RE: Loss of connection with PLC
Hello
Yes, I can see the PLC
in the appendix, the screenshots that I see
I checked the IP address on my router and it is 192.168.1.40
I already had problems when switching to 2.2, because by 2 times, the variables were duplicated, and the plc no longer worked, and I had to delete all the duplicate variables, and it's a big job[texte du lien]
(https://1drv.ms/u/s!Aq__SFpXusxkgbsO0aXb02aOyHXhSw?e=aNadYM)
https://1drv.ms/u/s!Aq__SFpXusxkyDClTBLXk0QoVXnV?e=0JOTym
https://1drv.ms/u/s!Aq__SFpXusxkgbsQjvU4ZrB13xv5kQ?e=YiRcp7
https://1drv.ms/u/s!Aq__SFpXusxkgbsN7vJdQ1gMJYMJqg?e=TwS47KThanks on adavance for you help
-
Loss of connection with PLC
Hello
I need your help, I no longer have communication with the PLC. I wanted to go from IDE 2.2 to 2.3 (with os 2.2) to do a scada project. When I uploaded, I lost communication. I already had several problems going from 2.0 to 2.2 because I had all the variables have been duplicated. I have attached a screenshot with the faults
https://1drv.ms/u/s!Aq__SFpXusxkgbsM6_HIUKDZaBI6aQ?e=S2MA0FThank you in advance for your assistance```
Insert Code Here -
Average a temperature measurement
Hello, I would like to make a sliding average of the 1-wire temperature measurement. AVG function blos average several probes. how can I do ? thank you in advance
-
RE: Light control and All Out
@ecobouwadvies Hello, I did all my lighting with the unipi and it works very well
I did a total closing function, and a patrial closing function to close only one homeland
it is not easy to explain, I attach my solution in the appendix. A word for the unipi team,> Mervis works very well, but is often quite difficult to start to connect variables and also to change version -
APP Mervis android
Hello
Is the mervis mobile app available? if yes, how to get the password
Thanks
-
Compatibility between Neuron with Mervis and Cayenne my-device
Bonjour
Hello
Would it be possible to install the Cayenne my-device software on a Neuron running Mervis
This in order to be able to access remotely and send notifications
If so, will cayenne have access to all the variables?thank you in advance