• Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Search
    • Register
    • Login

    How to connect UNICA and Unipi

    Scheduled Pinned Locked Moved Official API - Evok
    6 Posts 3 Posters 4.2k Views
    Loading More Posts
    • Oldest to Newest
    • Newest to Oldest
    • Most Votes
    Reply
    • Reply as topic
    Log in to reply
    This topic has been deleted. Only users with topic management privileges can see it.
    • M
      M4kr
      last edited by M4kr

      Hi there,

      I'm pretty new to the Unipi / Unica and the 1Wire bus.
      I've got the Unica U1WTVS sensor, the Unipi rev 1.1 board and of course a Raspberry Pi 3, running with raspbian Jessie.

      I read the Documentation and made an RJ45 cable like shown in the unipi manual. I connected the Pins to the UNICA Sensor. When I open the unipi control panel, no 1Wire devices are shown.

      So my question is, if there's a tutorial or explanation how to connect the unica sensor and get it's data on the control panel. Do I have to make some preperations in the evok api?

      edit: When I start the /opt/evok/evok.py i get the following message:
      Listening on port: 1025
      UniPi version:1.1
      Entering measure loop
      Entering 1wire loop
      Unsupported 1wire device DS2438 (2675FA0C02000054) detected

      I'm grateful for any help!
      Greetings
      M4kr

      1 Reply Last reply
      Reply Quote 0
      • D
        devien
        last edited by

        Hello M4kr,

        i've take same Sensors 1 y ago ant try'd to get running under fhem.
        maybe i can take temperature and 2two other values, but nobody here can tell how to convert correctly.
        so i can tell u one thing, the message "Unsupported 1wire device DS2438 (2675FA0C02000054) detected" tell you that your software dont know how to handle the device.
        Maybe i dont know evok, two things could be i think
        -first you need a definition of the DS2438 in evok to load (if it has one)
        -second you have to implement the definition yourself

        an DS2438 is wide known device, i think there would be anywhere a possible modul to load ;)
        my fhem know the DS2438, only the converting of the 2 values are tricky, anywhere u can change to fhem :)

        good luck

        1 Reply Last reply
        Reply Quote 0
        • M
          M4kr
          last edited by M4kr

          Hi devien

          Thank you very much for your reply.
          In the Unipi Control Panel, the device Sensor DS18B20 - 1
          is already shown.
          I found out, that in the /opt/evok/owclient.py the DS2438 is listed as a supported device (in the variable definitions).

          There was also a code block, which was commented out.
          In the /etc/evok.conf is only [SENSOR_1] (Type DS18B20) defined.
          So do I have to add the DS2438 as [SENSOR_2] in the evok.conf?

          Maybe you could provide me an example to get a better start into the world of 1wire :smirk:

          greetings
          M4kr

          T 1 Reply Last reply
          Reply Quote 0
          • D
            devien
            last edited by devien

            hi M4kr
            i think you mean

            elif (typ == 'DS2438'):

            return DS2438(address, typ, bus, interval=interval, circuit=circuit)

            as codeblock, i think it can help to uncomment this part. that show to be the part in evok owclient to give knowing of your batterymonitor-part of the unica device.

            maby you have to reload (better restart the system) to load the changed module.

            after this check if the DS2438 now be loadet

            well i'm not sure, but if this doesnt help you can roll back ;)

            one wire are most easy, there was o lot to read online, beginning at wikipedia ;)

            good luck

            PS: feedback after would be nice

            1 Reply Last reply
            Reply Quote 1
            • T
              tomas_hora administrators @M4kr
              last edited by

              @M4kr There are two parts that need to be uncommented. The definition of DS2438 claass and also enabling it in the code

              Reload evok and you should see the address of the sensor listed in the output of evok when runnin on hand: https://github.com/UniPiTechnology/evok#debugging (not in the WEB interface)

              Than you can create a new sensor in the evok.conf

              1 Reply Last reply
              Reply Quote 1
              • M
                M4kr
                last edited by M4kr

                Hi @devien hi @tomas_hora

                Thank you very much for your help. Life could be easy if you ask the right people ;-)
                I commented out the class definition but forgot enableing the DS2438 in the code. After fixing that, it seems to work fine.
                I'll edit this post if any errors occur in relation to the DS2438.

                Thanks again for your help.

                Greetings
                M4kr

                1 Reply Last reply
                Reply Quote 1

                Hello! It looks like you're interested in this conversation, but you don't have an account yet.

                Getting fed up of having to scroll through the same posts each visit? When you register for an account, you'll always come back to exactly where you were before, and choose to be notified of new replies (either via email, or push notification). You'll also be able to save bookmarks and upvote posts to show your appreciation to other community members.

                With your input, this post could be even better 💗

                Register Login
                • First post
                  Last post