Hello already for a long time we program the UNIPI via Mervis.. Now I would also start to use the Codesys.. I would like to know that image was preloaded on the Unipi... because in the Mervis there is an ISO image to be put on SD card.
Posts made by TriathletC
-
INFO Codesys
-
Enocean
I'm sorry I need information. The neurons I read about have the possibility of Mervis reading Enocean sensors. Now I would like to know .. if I buy Enocean wireless sensors ... can I interface them directly with Neurons?
-
RE: Tool Tips in HMI pannel...
Unfortunately I'm not practical .. could you help me?
-
Tool Tips in HMI pannel...
Good morning I would like to know if in Mervis in the software to create HMI .. it is possible to set the Tool tips on variables to read and buttons .. I would create a HMI for blind people .. and I needed the tool tips function to associate it with the application of windows 10 that reads at the hover and translates into audio.
-
AO signal 0-10 V in parallel
Sorry guys you can drive two modulating valves 0-10v with a single AO signal of the neuron? Put the parallel signal from problems at the analog output? does it hold the load?
I need to know this because I definitely have to drive in parallel with a single 0-10v signal two fancoil with inverter ..
-
RE: barometric sensor on i2c
In theory and in practice you have to try to connect it and make attempts ... with the existing libraries.
-
barometric sensor on i2c
hello I would like to know if it was possible to acquire and install a barometric sensor on I2c bus.The following is used as an I2c library.
-
RE: M-Bus in Neuron (for heat meters)
I apologize, I wrote the domnda badly before.
I ask if I had to interface with the type of probes that communicate in Modbus rtu a ... is it possible to connect them directly without any converter or gateway to the NeoRon Rs485? -
RE: M-Bus in Neuron (for heat meters)
Forum use a modbus rtu accessories, you do not need any right gateways? just connect the two wires to the rs485 neurinoma port right?
-
M-Bus in Neuron (for heat meters)
Hello everyone, I would like some detailed information if possible about the 485 port of the Neuron.I I have 40 counters and I should connect them to a Neuron..the bus used is a two-wire M-bus ... I would like to know if I can directly attack this bus directly to the gate 485 of the Neuron.I would like to know in addition how it should or I will have to do to read the counters already installed in the field .. I talk about using the Mervis programming software .. You can send me a tutorial something like that where you can take inspiration ?.
I also wanted to know if these 40 counters I could put them in 40 well-defined historians in order to calculate an average annual consumption.
if so how should I do? Thank you -
RE: Supervisor with use 10 Neuron
I apologize if I use 10 Neurons connected via a TCP network with IP inequalities of the same family, is it possible to contract HMI graphics all the Neuron PLCs in one?
Type a master to make us clear.
If yes, how should I do?
could you send me an example via screenshoot? thank you -
Supervisor with use 10 Neuron
Good evening I need information for a client.
I would like to know if I would build a complex system with 10 neuron PLCs .. all connected by RS485 bus .. I would like to know if using only a Neuron of 10 connected all in series / parallel .. you can create the graphics through the mervis all on one PLC enclosing all the points but all the other 9 remaining PLC..Type concentrator .. I would also like to know if all the points created and made visible in the engine .. can be inserted and viewed by a classic scada system .. with mdbus protocol ..
is it possible to connect all the Neurons via rs485..but only one of them connect it to a scada system connected to it via TCP?
Thank you -
button creation
good sers I need technical information. I have to create a button to close the shutters .. I can not ..
The problem as you can see for the activation with the classic button I first forced to put OFF then click on reset ..
Actually I would like to create a button with a single push .. that self resets itself ... how should I do?
-
Ni1000 in the Neuron
Good morning i have one question..Is possible insert the sensor resistor Ni1000 in Analog input?But in the Mervis in al ready...this option...
-
RE: Password HMI
I have not received your email to be able to download the beta version .. you could kindly send it back to my email thanks
-
Password HMI
Good evening .. I ask a little help .. I entered username and password as a screen that I attach .. but when I go to open the HMI through the web .. does not require me to enter any user and password ..
but it makes me see all the panels and makes me use everything .. and it's not okay I should protect everything from password .. -
Setting Networking send the mail
Good morning I need to know how I should set the gateway and DNS to send mail .. using gmail .. thanks