• Register
    • Login
    • Search
    • Categories
    • Recent
    • Tags
    • Popular
    • Users
    • Groups
    • Search
    1. Home
    2. ChuckMountain
    C
    • Profile
    • Following 0
    • Followers 0
    • Topics 2
    • Posts 6
    • Best 0
    • Controversial 0
    • Groups 0

    ChuckMountain

    @ChuckMountain

    0
    Reputation
    552
    Profile views
    6
    Posts
    0
    Followers
    0
    Following
    Joined Last Online

    ChuckMountain Unfollow Follow

    Latest posts made by ChuckMountain

    • RE: Migrating to the latest version of Mervis from 2.0.10

      I thought it might have been a lack of IP address in the TCP Modbus connector so did a rebuild.

      However, it started working before I changed it so perhaps the install did not complete correctly the first time around. Oh well, a somewhat frustrating amount of time wasted :)

      posted in Mervis
      C
      ChuckMountain
    • Migrating to the latest version of Mervis from 2.0.10

      So it has been a while since I last updated my UniPi but was going round updating various machines and wanted to migrate to the latest version.

      I cannot however, get the digital inputs to be either found or recognised, in debug mode they always come back as false. I have tried the old solution, a brand new solution etc. but nothing wants to pick them up. The relays and temperature gauges work fine and get read and can be set (via a NOT) however I can't seem to pick them up so my code won't work.

      My code is simple in that when a couple of inputs go high they should flip the relay. It has been working fine and reverting back to the original uSD card image works fine.

      I assume it is something to do with the pull up\down resistor setting but I can't see anyway of setting it properly.

      Hardware is a Pi 2 and UniPi 1.1

      Installed the latest version of the OS Image on as well as the RT.

      Any ideas please?

      posted in Mervis
      C
      ChuckMountain
    • RE: Fhem Not detecting 3 inputs

      Done some more testing and I currently wanting to use 4 inputs and 2 have ~ 5.5V and 2 have ~12V.

      I have all the jumpers set to the writing side as per instructions.

      If I have inputs connected to 1 and 2 with both ground to P02 with 5.5V they work fine and detect correctly.

      If I then have additional inputs connected to what appears to be anything else and P01 with 12V they are also detected correctly.

      However if I reboot with Fhem then I don't get any inputs working until I disconnected the grounds from P01 or P02 and then reconnect and all appear to detect input correctly. This also appears to fix 7 and 8 displaying ???

      If I try using Evok on a different build then it correctly detects them all without any wiring changes so something software based is happening in the Fhem configuration.

      However I am new to Fhem so trying to figure out what is causing this repeatable behaviour.

      Any ideas? Also are 5 and higher inputs supposed to be green LEDS ?

      Thanks for your help

      posted in FHEM.de
      C
      ChuckMountain
    • RE: Fhem Not detecting 3 inputs

      I had originally setup my 2 inputs on inputs 3 and 4.

      I changed to put on 1 and started up. Same difference. When I toggled the power to input it detected it ok and changed to a light bulb.

      Toggled input and then changed now correctly to off light bulb.

      This seems to persist after reboot so input 1 seems ok now.

      Inputs 7 and 8 are still the same but I assume if I test them in the same manner they would work too.

      Any ideas what causes this or if I can set 7 and 8 without having to rewire?

      posted in FHEM.de
      C
      ChuckMountain
    • RE: Fhem Not detecting 3 inputs

      Have set the UniPi with the B+ bought as the kit from here. Have downloaded FHEM and setup however 3 of my inputs are showing as ???. They are 1, 8 and 9.

      Have I missed something obvious in the settings to enable these?

      posted in FHEM.de
      C
      ChuckMountain
    • Fhem Not detecting 3 inputs

      Have set the UniPi with the B+ bought as the kit from here. Have downloaded FHEM and setup however 3 of my inputs are showing as ???. They are 1, 8 and 9.

      Have I missed something obvious in the settings to enable these?

      posted in FHEM.de
      C
      ChuckMountain