Hi Thomas,
after boot I stopped evok and start it again manually.
pi@S103-sn291:/opt/evok $ sudo python evok.py
[I 180314 17:15:28 config:63] eprom: UniPi Neuron S103 version: 1.0 serial: 0x123
[I 180314 17:15:28 evok:1628] Starting using config file /etc/evok.conf
[I 180314 17:15:29 config:75] YAML Definition loaded: L20x.yaml, type: 3, definition count 0
[I 180314 17:15:29 config:75] YAML Definition loaded: M30x.yaml, type: 3, definition count 1
[I 180314 17:15:29 config:75] YAML Definition loaded: L50x.yaml, type: 3, definition count 2
[I 180314 17:15:29 config:75] YAML Definition loaded: S10x.yaml, type: 3, definition count 3
[I 180314 17:15:29 config:75] YAML Definition loaded: xS40.yaml, type: 3, definition count 4
[I 180314 17:15:29 config:75] YAML Definition loaded: M10x.yaml, type: 3, definition count 5
[I 180314 17:15:30 config:75] YAML Definition loaded: L30x.yaml, type: 3, definition count 6
[I 180314 17:15:30 config:75] YAML Definition loaded: M50x.yaml, type: 3, definition count 7
[I 180314 17:15:30 config:75] YAML Definition loaded: L51x.yaml, type: 3, definition count 8
[I 180314 17:15:30 config:75] YAML Definition loaded: xS30.yaml, type: 3, definition count 9
[I 180314 17:15:30 config:75] YAML Definition loaded: M40x.yaml, type: 3, definition count 10
[I 180314 17:15:31 config:75] YAML Definition loaded: M20x.yaml, type: 3, definition count 11
[I 180314 17:15:31 config:75] YAML Definition loaded: CUSTOM MODBUS DEVICE.yaml, type: 3, definition count 12
[I 180314 17:15:31 config:75] YAML Definition loaded: L40x.yaml, type: 3, definition count 13
[I 180314 17:15:31 config:75] YAML Definition loaded: xS10.yaml, type: 3, definition count 14
[I 180314 17:15:31 config:75] YAML Definition loaded: xS50.yaml, type: 3, definition count 15
[I 180314 17:15:31 config:75] YAML Definition loaded: evok-alias.yaml, type: 2, definition count 0
[I 180314 17:15:31 evok:1692] HTTP server listening on port: 8080
[I 180314 17:15:31 modbusclient_tornado:122] SPI client started
[I 180314 17:15:31 neuron:157] Reading SPI boards
[D 180314 17:15:31 owclient:377] Entering 1wire loop
[I 180314 17:15:31 neuron:172] No board on SPI 2
[I 180314 17:15:31 neuron:172] No board on SPI 3
Then I try to connect with a browser bolded text http://192.168.200.188, the Control Panel is loaded,
without any Outputs or Inputs as described in my first post.
But if I try to connect with port 8080: bolded texthttp://192.168.200.188:8080
I get this message.
[W 180314 17:15:42 web:2063] 404 GET / (192.168.200.105) 5.97ms
Which serverprocess is listening to port 8080 ?